Rubber Seal, 5 Port Solenoid Valve, Series SZ3000 6 (L4) Applicable connector: 20 pin MIL type with strain relief L3 U side D side Connector entry direction switch 6.6 (3.2) 101.2 (conforms to MIL-C-83503) 3.1 8 36.3 5.5 5.3 LOCK FREE Triangle mark 35 18 28.8 A B A B 47.6 A A A 58.2 DIN rail 6 Triangle mark position 7.9 Manual override 22 36.1 In case of locking type, turn after pushing in. ( ) 3.5 (With switch) Power supply terminals (M3
price of compressed air: 3 yen/m3 (ANR) Pressure: 0.5 MPa Operation time of the compressor: 2,500 h/year To reduce pressure loss: 1 Regulate at the proper pressure. 2 Reduce the restriction and pressure loss on the fittings. 3 Improve the effective sectional area ratio of the nozzle to the inlet side by adopting a nozzle with a small diameter.
A side: Orange (for supply valve) B side: Green (for release valve) Release flow adjustment needle (With light/surge voltage suppressor) 33.3 4.4 Pressure setting trimmer Pilot valve exhaust port Hysteresis setting trimmer (M3: Port PE) Silencer (AN203-KM8) 57.1 62.1 47.5 39.7 29.5 21 33.6 23.5 10 Vacuum port (5.25) (13.5) 3.75 (8.25) 6 One-touch fitting Port V Supply port 16.75 88 19 Button
Screw material SUS Screw dimensions M3 x 0.5 Recommended tightening torque [Nm] 0.48 to 0.63 L1 (Maximum screw-in depth) [mm] 4.6 L2 (Plate thickness) [mm] 2.1 2) Card Motor mounting from above / through hole.
Description Material Note 1 Bracket set SFD-BR100 With 2 countersunk head screw (M3) 5. Maintenance The element of this product cannot be disassembled or replaced. It is therefore necessary to replace the entire housing to replace the element.
If the solenoid valve and the manifolds pilot EXH (PE) port is restricted extremely or blocked, abnormal operation of the solenoid valve may occur. 1) When using SMCs M3 or M5 fittings, follow the procedures below to tighten them. Connection thread: M3 First, tighten by hand, then use a suitable wrench to tighten the hexagonal portion of the body an additional 1/4 turn.
0.450.6 Nm M3 0.81.2 M4 1.42.5 13 No.VFS4000-OMY0001 11 1 2 3 14 No.VFS4000-OMY0001 EXH.
m3/sN02NPT1/4118 g90 gC01Rc1/8114 g86 g1 x 10?5 Pa?m3/s
m3/sN02NPT1/4118 g90 gC01Rc1/8114 g86 g1 x 10?5 Pa?m3/s
, m3 x 103, ft3, ft3 x 103, ft3 x 1060.1 to 1.5 MPa2.25 MPa20 kPa (at maximum flow rate)0 to 9,999,999,999 l?
, m3 x 103, ft3, ft3 x 103, ft3 x 1060.1 to 1.5 MPa2.25 MPa20 kPa (at maximum flow rate)0 to 9,999,999,999 l?
m (95% filtered particle size)Max. 0.1 mg/m3 (ANR) (Before saturated with oil: 0.01 mg/m3 (ANR) or less, approx. 0.008 ppm) (2)PolycarbonateOption80.18
m (95% filtered particle size)Max. 0.1 mg/m3 (ANR) (Before saturated with oil: 0.01 mg/m3 (ANR) or less, approx. 0.008 ppm) (2)PolycarbonateOption80.18
m (95% filtered particle size)Max. 0.1 mg/m3 (ANR) (Before saturated with oil: 0.01 mg/m3 (ANR) or less, approx. 0.008 ppm) (2)PolycarbonateOption80.18
m (95% filtered particle size)Max. 0.1 mg/m3 (ANR) (Before saturated with oil: 0.01 mg/m3 (ANR) or less, approx. 0.008 ppm) (2)PolycarbonateStandard250.22
m (95% filtered particle size)Max. 0.1 mg/m3 (ANR) (Before saturated with oil: 0.01 mg/m3 (ANR) or less, approx. 0.008 ppm) (2)PolycarbonateStandard250.22
m (95% filtered particle size)Max. 0.1 mg/m3 (ANR) (Before saturated with oil: 0.01 mg/m3 (ANR) or less, approx. 0.008 ppm) (2)PolycarbonateStandard450.44
m (95% filtered particle size)Max. 0.1 mg/m3 (ANR) (Before saturated with oil: 0.01 mg/m3 (ANR) or less, approx. 0.008 ppm) (2)PolycarbonateStandard450.44
m (95% filtered particle size)Max. 0.1 mg/m3 (ANR) (Before saturated with oil: 0.01 mg/m3 (ANR) or less, approx. 0.008 ppm) (2)PolycarbonateStandard450.44
Thread sizes range from M3 to 2 and are available in both inch (NPT) and metric R/Rc(PT)Large flow in-line style, Body sizes: 1/2, 3/4, 1, 1-1/4, 1-1/2, Port sizes: 1/4, 3/8, 1/2, 3/4, 1, 1-1/4, 1-1/2, 2, SPEED CTRL, M3 THREAD, AIRLINE EQUIPMENT, AS FLOW CONTROL, 1B, AS OTHER SIZE STANDARD (PT), .04922 lb