SMCs vertical type LEHZ, 2-finger electric grippers are structured to maintain workpiece gripping force in the event of an emergency stop or restart. An encloder makes it possible to confirm positioning and to output length measurements.

SMCs vertical type LEHZ, 2-finger electric grippers are structured to maintain workpiece gripping force in the event of an emergency stop or restart. An encloder makes it possible to confirm positioning and to output length measurements.

SMCs vertical type LEHZ, 2-finger electric grippers are structured to maintain workpiece gripping force in the event of an emergency stop or restart. An encloder makes it possible to confirm positioning and to output length measurements.

It may be possible if the operating stroke of the air gripper magnet (piston part) is long and the stroke difference of the fingers can be sufficiently ensured. However, 1 switch is required to detect each position. Note that the switch set to detect workpiece gripping often remains ON when fully open to grip the inner diameter of a workpiece and when fully closed to grip the outer diameter

An adapter for the ZPT series.Features· Single adapter.· Symbol 1: pad diameter 2 to 8 mm.· Symbol 2: pad diameter 10 to 16 mm.· Symbol 3: pad diameter 20 to 32 mm.· Symbol 4: pad diameter 40 mm / 50 mm.Applications· A replacement part for ZPT series vacuum pads.

Series IDF can accommodate an inlet temperature o, front panel IDH6-10, THERMO DRYER, 769, 5 lb

Series IDF can accommodate an inlet temperature o, Rear Panel A IDH6-10, THERMO DRYER, 769, 5 lb

Series IDF can accommodate an inlet temperature o, Rear Panel B IDH6-10, THERMO DRYER, 769, 5 lb

Series IDF can accommodate an inlet temperature o, Left Side Panel IDH6-10, THERMO DRYER, 769, 5 lb

Yes. Refer to the operation manual on the SMC website for details. The SI unit part number (EX□-□) is determined by the valve manifold model. Refer to the SI unit part numbers in the valve catalog.

(Reference) Although the measurement method is different, we have released an actuator position sensor which can be mounted on a standard cylinder to output the stroke position with an analog signal. The D-MP series catalog can be found here.

The “-XB14” uses an “-XB6” heat-resistant cylinder (with heat-resistant seal material and grease) with a built-in heat-resistant magnet (for CDQ2 series cylinders).

In addition, an MGPS series heavy-duty guide rod type compact guide cylinder is available for bore sizes ø50 and ø80 (and can be used as a stopper for strokes up to 50 mm).

Return to origin is performed by a push return to origin at the stroke end (the table goes to the stroke end and the position 2 mm in reverse is taken as the origin), so no sensor is required.

For the AQ240F, there are ø4, ø6, or ø1/4 One-touch fittings, and for the AQ340F, there are ø6 or ø1/4 One-touch fittings. ø8 One-touch fittings are available as a special order. (e.g., AQ340F-08-00-X512, etc.) Consult your local SMC sales office for further details. The AQ240F/340F series catalog can be found here.

Compared with an ANA1 with the same male thread size, the external dimensions are also larger.
AN□02 series: It features 35 dB(A) noise reduction, and uses flame-resistant material (equivalent to UL-94 standard V-O) for the main body. Only 1/4, 3/8, and 1/2 port sizes are available.
(Reference 1) Standard AN series compact resin type silencer: 30 dB(A) noise reduction

Either AC or DC can be selected for the voltage type (AC or DC can be indicated when selecting an indicator light). The GP46 series catalog can be found here.

Refer to the dimensions below. Also, when performing drain piping for the drain piping type, be sure to secure additional maintenance space as required.
・AMC220, AMC310, and AMC320: 20 mm
・AMC510 and AMC520: 35 mm
・AMC610: 60 mm
・AMC810: 110 mm
・AMC910: 140 mm

HRS□□ series thermo-chillers can be remotely operated (run/stop) by applying a contact signal input.
First, refer to the “Transport and Setting Up” section in the HRS series operation manual.
Wiring examples are shown in the “Wiring of remote operation signal input” and “Wiring of run/stop signal input・Remote signal input” sections.
Next, to enable remote signal input, change

The presence or absence of an air release valve is as follows.