SI unit for PROFIBUS DP M3 x 30 screw for connection to the valve manifold. 1: For details of suitable cables refer to the Accessories section on page 32. 2: Refer to page 17 for the LED Indication and Settings. -10No.EX-OMN0009-G Installation and Wiring Installation Connect valve manifold to the SI unit.
Instructions 3 Product Summary 8 System configuration 8 EX500 GW unit Model indication and How to order 9 Summary of Product parts 9 Mounting and Installation 10 Installation 10 Wiring 10 Setting 18 Specification 22 Specifications 22 Dimensions 24 SI unit Model indication and How to order 25 Summary of Product parts 26 Mounting and Installation 27 Installation 27 Setting 29 Specification 30
Warning Caution Connection thread Proper tightening torque ( ( ( (N m) Rc1/8 7 to 9 Rc1/4 12 to 14 Rc3/8 22 to 24 Rc1/2 28 to 30 Rc3/4 28 to 30 Rc1 36 to 38 Rc1 1/4 40 to 42 Rc1 1/2 48 to 50 Rc2 48 to 50 5. Connection of piping to products When connecting piping to a product, refer to its operation manual to avoid mistakes regarding the supply port, etc. 6.
GMJ1 Series Table of Contents Safety Instructions 3 Model Indication and How to Order 8 Summary of Product Parts 9 Definition and terminology 10 Common Specifications 12 EX510 GW Unit Summary of Product Parts 13 Mounting and Installation 14 Installation 14 Wiring 15 Setting 20 Specifications 26 Specifications 26 Dimensions 27 SI Unit Summary of Product Parts 28 Mounting and Installation 30
Note 10: Delay of binary output Binary output is delayed for 30 ms or less. Reading of binary output shall be done only when cylinder stop output is ON. About "Cylinder stop output" There are cases where cylinder stop output is output when cylinder stops temporarily due to knocking and cylinder operates at extremely low speed. In such cases, provide longer time to output.
Tightening Torque for Piping Connection thread Proper tightening torque (Nm ) Rc1/8 7 to 9 Rc3/8 22 to 24 Rc1/2 28 to 30 Rc3/4 28 to 30 Follow the procedure of the manufacturer when fittings other than SMC is used. Wiring Caution 1. Polarity There is no polarity. 2. Applied voltage When electric power is connected to a solenoid valve, be careful to apply the proper voltage.
Standard stroke (mm) Bore size 50 63 80 Extended 40.3 78.5 88.2 Retracted 139.5 174.6 217.3 Bore size Standard stroke 50 30 63 30 80 40 1-4. Cylinder mass Action Bore size Mass (mm) (kg) 50 1.70 Double acting Single acting (spring retraction) Double acting with spring 63 2.78 80 4.96 4 - 2.
Rc 1/2 28 to 30 Compressed air containing a large amount of drainage can cause malfunction of pneumatic equipment. An air dryer or water separator should be installed upstream from filters. 6. Piping to products When piping to a product, avoid mistakes regarding the supply port, etc. 3.
Take appropriate measures so that a force of 30 N or more is not applied to the lead wire. When instructions are given in the Specific Product Precautions, follow these specifications. Lubrication 1.
Auto switch type for rotary actuator 30 Auto switch specification 31 Proper auto switch mounting position and operating range 32 Cautions on mini rotary actuator with auto switch 33 Maintenance and Inspection 33 Periodic inspection 33 External stopper assembly procedure 35 Troubleshooting -1- Safety Instructions These safety instructions are intended to prevent hazardous situations and/or
Warning Caution Rc1/8 7 to 9 Rc1/4 12 to 14 Rc3/8 22 to 24 Rc1/2 28 to 30 Rc3/4 28 to 30 Rc1 36 to 38 Rc1 1/4 40 to 42 Operating Precautions 1. Valves will reach high temperatures from high temperature fluids. Use caution, as there is a danger of being burned if a valve is touched directly. 2.
Pin Cylinder Series CJP Double Acting/Single Acting Spring Return Variations Series Action Standard Variation Bore Size (mm) Standard Stroke (mm) Page CJ1 Built-in Magnet CJP Standard Style Series CJP Double Acting (Non-lube) 6 5,10,15,20 10,15 5,10,15,20,(25),30 Single Rod 1.2-2 6 CJ2 10 CM2 Single Rod Spring return Single Acting (Non-lube) 15 5/10/15 1.2-8 C85 CG1 How to Order/Double Acting
Unsuccessful home position return 30 Trying to execute a program/step without completing the setup (home position return). No designated speed 31 No speed designation with MOVA or MOVI, and no prior speed designation found. No jump destination 32 No label found at the program designated jump destination.
For standard installation, turn 15 to 30 using tool, after fastening by hand. Pay attention not to over torque the product.
30 days based on JIS B 8374-1981) Max. 50C Ambient and fluid temperature Lubrication Not required (Use turbine oil Class 1 ISO VG32, if lubricated.)
Ambient and fluid temperature (C) Response time (ms) (1) (at the pressure of 0.5 MPa) 0 (No freezing) to 60 OFF AC 30 or less ON AC 30 or less DC 30 or less DC 40 or less Max. operating frequency (Hz) 3 Required (Equivalent to turbine oil Class1 ISO VG32) Lubrication (2) Yes (Non-locking) Manual override Mounting orientation Unrestricted 150/50 Note 1) Based on dynamic performance test, JIS
80 or less 180 or less 180 or less 30 or less 60 or less 300 or less 180 or less 0.8 1.4 100 90 20 14 13.2 Response time (1) (ms) VFN Max. operating frequency (c.p.m.) (2) DC AC DC AC 1.6 2.4 300 360 50 60 24 Weight (kg) 50 Hz Apparent power (VA) Inrush 60 Hz AC 50 Hz Holding 60 Hz Power consumption (W) DC Note 1) Based on JIS B 8375-1981.
Operating pressure range 101.2 kPa to 0.1 MPa Apparent power/AC Inrush Holding 7.9VA (50 Hz) , 6.2VA (60 Hz) 5.8VA (50 Hz) , 3.5VA (60 Hz) Power consumption/DC 2 W, 2.2 W (With indicator light) 30 ms or less (at the pressure of 0.5 MPa) Response time (1) Note1) Refer to Response time of standard specifications.
.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com (2) End plate DIN rail clasp When a manifold contains a large number of stations and is difficult to remove all at once, separate the manifold into several sections before removing it. 30 41 1 2 Mounting and Removal of Valves Mounting Manifold on DIN