Pin Clamp Cylinders A: Lock unit holding bolt R 075 CKQG32X B 08 CKQG32X CK1 B: Cylinder holding bolt Guide pin diameter * Refer to Table 1 (Symbol 2) below. Applicable hole diameter of workpiece * Refer to Table 1 (Symbol 1) below.
(B contact). Contact output signal 3 WRN alarm selects N.O. (A contact) or N.C. (B contact). (1) (2) (3) Setting of contact output signal 1 to 3 Table 5.4-28 Setting of contact output signal 1 to 3 No.
4413: Hydraulic fluid power -General rules relating to systems IEC 60204-1: Safety of machinery -Electrical equipment of machines (Part 1: General requirements) ISO 10218: Manipulating industrial robots-Safety JIS B 8370: JIS B 8361: JIS B 9960-1: (1 : ) JIS B 8433: *2) 1. 2. 3. 1. 2. 3. 4
Model A side B side JIS Symbol A relay output module of devices up to 110 A B is available for control VAC, 3 A. 4(A) 2(B) A B N.C. valve N.C. valve 3(EB) SOL.b SOL.a 1 2 SV A00 5(EA) B side passage symbol: Green B side manual override: Green Tie-rod base manifold (For SV1000/2000/3000/4000) 1(P) 4(A) 2(B) A side coil A side spool valve B side spool valve N.O. valve N.O. valve 1 2 SV B00
(Tolerance 30%) Hysteresis may fluctuate due to the operating environment. 1 pc. 2 pcs. 1 pc. 2 pcs. 1 pc. 2 pcs. 10 10 5 5 10 15 Auto Switch Mounting Bracket/Part No.
4 @1 u q !3 !2 @6 t @4 w @8 r !1 @5 @3 @2 e !6 A A C B M(D)LUB25 y !9 i o !5 @0 Extension locking w q Section A-A !
Grommet Plug-in, L plug connector, M plug connector (With light/surge voltage suppressor) Electrical entry Normally open VQZ (A) 2 Note 1) Based on JIS B 8374-1993.
12 V Coil rated voltage DC S070 10% of rated voltage Allowable voltage fluctuation (A) 2 Class B or equivalent Coil insulation type VQ Power consumption (Current) 0.5 W (21 mA) 1 W (42 mA) 1.5 W (63 mA) 1 (P) 3 (R) DC VKF Grommet Plug-in, L plug connector, M plug connector (With light/surge voltage suppressor) Electrical entry Normally open VQZ (A) 2 Note 1) Based on JIS B 8374-1993.
Nominal thread size Tightening torque Rc(NPT)3/8 15 to 20 Nm Rc(NPT)1/2 20 to 25 Nm Rc(NPT)3/4 28 to 30 Nm Rc(NPT)1 36 to 38 Nm Rc(NPT)1 1/4 40 to 42 Nm Rc(NPT)1 1/2 48 to 50 Nm If the tightening torque is exceeded, the product can be broken. If the correct tightening torque is not applied, the fittings may become loose. Avoid any sealing tape getting inside the piping.
V Coil rated voltage DC S070 10% of rated voltage Allowable voltage fluctuation (A) 2 Class B or equivalent Coil insulation type VQ Power consumption (Current) 0.5 W (21 mA) 1 W (42 mA) 1.5 W (63 mA) 1 (P) 3 (R) DC VKF Grommet Plug-in, L plug connector, M plug connector (With light/surge voltage suppressor) Electrical entry Normally open VQZ (A) 2 Note 1) Based on JIS B 8374-1993.
) Main port 1(A) (Back side 2(B)) Port size: refer to table below 65 (Grommet terminal: E) 70 (Conduit terminal: T) 74.5 (DIN terminal: D) Bracket 2 x M4 x 0.7 depth 7 2 x 4.5 Main port 1(A), 2(B) Model VNA1-6A VNA1-8A VNA1-10A 1 8 1 4 3 8 In the case of EZ or TZ, the length is longer by 10 mm.
How to change the number of cups 6.1 Change to 1 cup (with flange) 1. Removal of the cup. (1) Remove the suction cup with adapter from plate B using a spanner. (2) Loosen the bolt (M4x8), then remove plate B from plate A. Be careful not to lose the O-ring. (3) Loosen the bolt for sealing (M6x8), then remove the cup from plate A. Completion drawing 2.
Normal output Reversed output P_1(P_2)=A-(A-B)/4 n_1(n_2)=B+(A-B)/4 A = Maximum pressure H_1(H_2)= (A-B)/2 H_1(H_2)= (A-B)/2 B = Minimum pressure If setting is not necessary press the UP and DOWN buttons simultaneously for 1 second or longer. -37No.PS-OMY0007-A [F 6] Fine adjustment of display value This function is to manually perform a fine adjustment of the displayed pressure value.
K: Non-rotating D-D B B Width across flats 19 Width across flats 19 D D D D 22 28 A B 50 5 5 22 28 A B 50 5 5 M14 x 1 M8 x 1.25 Gasket M8 x 1.25 Gasket M14 x 1 Width across flats 21 Width across flats 21 50 4 50 4 4.5 4.5 Dimensions Dimensions Part no.
M8 x 1.25 LA 11 12 14 MB M6 x 1 M8 x 1.25 M10 x 1.5 LB 9.5 16 15 MC M5 x 0.8 M6 x 1 M8 x 1.25 LC 9.5 12 12 MD 9 11 14 LD 5.5 6.5 8.5 ND 5.6 6.8 8.6 PA Rc 1/8 Rc 1/8 Rc 1/4 PB Rc 1/16 Rc 1/16 Rc 1/8 Model ML2B25 ML2B32 ML2B40 716 Stroke Reading Rodless Cylinder with Brake ML2B Series With stroke sensor: With brake: ML2B Bore size S Stroke ML2B Bore size B Stroke CEP1 N K M 9 N K M O H 1 CE1
0 @1 Stopper Resin !1 Replacement Parts Cover !
Allowable kinetic energy E max. : Table 1 Possible to use by E=0.018
How to change the number of cups 6.1 Change to 1 cup (with flange) 1. Disassemble the suction cups with adapter. (1) Remove the suction cup with adapter from plate B using a spanner. (2) Loosen the bolt (M4 x 8), then remove plate B from plate A. Be careful not to lose the O-ring. (3) Loosen the bolt for sealing (M6X8), then remove the cup from plate A. Completion drawing 2.
Indication Item Setting and selection *1 A contact (normally open) Contact type B contact (normally closed) *1 Alternate Signal form (1) Input 1 Contact input signal 1 Momentary [Off] Disabled [External Switch] External switch signal Signal type [Run/Stop] *1 Run/stop signal [Run] *2 Run signal *1 A contact (normally open) Contact type B contact (normally closed) *1 Alternate (2) Input 2
0.024 0.008 0.016 V114 V114A V124 Note 1) V124A Note 1) Note 1) For both V124 and V124A, pressure from port 3 and exhaust from port 1.