VEX-OMT0003 The suppressor residual leakage voltage should be as follows.
Table symbols : Can be used. : Cannot be used. : Can be used under certain conditions. Please consult us.
Therefore, the flow rate can be measured by detecting this frequency.
Table symbols : Can be used. : Cannot be used. : Can be used under certain conditions. Please consult us.
Therefore, the equipment to be connected must be below this rating.
For the analog output type, when ON the output will be 5 V or 20 mA, and when OFF, it will be 1 V or 4 mA.
IDX-OM-X004-D PRODUCT NAME Heatless Air Dryer MODEL / Series ID20-02 ID30-04 ID40-04 ID60 -06 Please read this manual prior of using the air dryer. Keep the manual readily available for reference. To Customers Thanks for purchasing SMC Heatless Air Dryer. This opertion manual must be read and understood throughoutly before handling.
Otherwise, lock may not be engaged. u Use complete stroke or cylinder at side with lock. If cylinder piston does not reach end of stroke, lock may not be engaged or released. 2. Operating pressure Lock Caution Release Use pressures 0.15 MPa or more at port with locking mechanism. Otherwise, lock will not be released. 3.
Please be sure to fill in the blank referring to page 646.
NO YES YES With connector: Within 20.5 mm NO The system cannot be used because if the proper air balance cannot be attained, an excessive load will be applied to the brake unit. Can the proper air balance be attained in accordance with the cylinder's mounting orientation?
Therefore, the equipment to be connected must be below this rating.
ASD Model Meter-out type Rod and applicable tubing O.D. 4 6 8 10 Meter-in type AS1000P-04-04 AS2000P-04-04 AS2000P-06-06 AS2500P-06-06 AS3000P-08-08 AS3000P-10-10 AS1010P-04-04 AS2010P-04-04 AS2010P-06-06 AS2510P-06-06 AS3010P-08-08 AS3010P-10-10 AS AS-FE KE
The shorter the distance from the cylinder (the shorter the piping), the shorter the overrun amount will be, and stopping accuracy will be improved.
The larger the effective area is, the shorter the locking time will be (the overrun amount will be shorter), and stopping accuracy will be improved.
Be sure to operate with a drain trap installed. 7. When connecting piping to a valve, be sure to tighten while holding the valve with a wrench or other tool. 11 Series VCS Direct Operated 2 Port for Steam 2 Port Solenoid Valve for Fluid Control/Precautions 3 Be sure to read before handling Operating Environment Wiring Warning Caution 1.
Therefore, SMC products cannot be used for business or certification ordained by the metrology (measurement) laws of each country. Safety Instructions Be sure to read the Handling Precautions for SMC Products (M-E03-3) and Operation Manual before use.
BA -08 BA -10 BA -32 BA -02 BA -01 CX D-G5NBL 35 40 45 45 45 40 50 45 D-G5/K5 D-B7/B8 BM1 -01 BM1 -02 BM1 -32 BM1 -04 BM1 -05 BM1 -06 Since this is a guideline including hysteresis, not meant to be guaranteed.
The instruction manual should be carefully read and fully understood before the product is installed and operated. Also, the manual should be kept where it can be easily referred to at any time. 2. Allow space for maintenance. Allow the space necessary for maintenance and inspections. 3. Tighten screws with the proper tightening torque.
If the socket will be used again, first spread the hook outward. Connector Socket Lead wire Hook 4-4-57 58 Series SYJ300/500/700 Specific Product Precautions 3 Be sure to read before handling.
Since the products specified here are used in various operating conditions, their compatibility for the specific pneumatic system must be based on specifications or after analysis and/or tests to meet your specific requirements. Be particularly careful in determining the compatibility of the fluid to be used. 2.