SMC Corporation of America
Elite Part Number Search
Search Results "VV317-02-051-02N-A-Q"

VER VEA 5 (R1) 4 (A) 1 (P) 2 (B) VY2 OFF state VBA VBAT F1 < F2 condition: See figure q. 2 (B) 3 (R2) AP100 4 (A) ON state Immediately after turning on F1 > F2: See figure e.

Bore size (mm) Auto switch model 20 25 32 40 50 63 80 100 D-C7/C8 BMA2-020 BMA2-025 BMA2-032 BMA2-040 BMA2-050 BMA2-063 D-H7 D-B5/B6 BA-01 BA-02 BA-32 BA-04 BA-05 BA-06 BA-08 BA-10 D-G5/K5 A set of following stainless steel mounting screws is attached. (A switch mounting band is not attached. Please order the band separately.)

CD-P11 CD-P12 2 Contact Protection Box/Dimensions Contact SMC when using built-in contact protection circuit style (D-A34[A] [C], D-A44[A] [C], D-A54/A64, D-B54/B64, D-A59W, D-B59W) in the following conditions: q The wiring length to load is more than 30m. w When using PLC with large flow current Contact Protection Box/Specifications Load voltage CD-P11 CD-P12 Part No. 100V AC max. 200V AC

specications VQ 1/2 Type of actuation Nil Q CE-compliant 2-position single 3-position closed center Nil Side ported B Bottom ported VQ 4/5 VQ 4/5 (A) 4 (B) 2 (A) 4 (B) 2 1 3 Note) CE-compliant: For DC only.

Select the point of contact A of inlet pressure and max. air capacity in the graph. 2. To select one with the maximum air flow rate line that is located above the obtained intersection point A, the model will be AFF37B.

The mist then coagulates to form a large drop, becomes separated from the compressed air, accumulates in case r , and is discharged through the drain valve. Meanwhile, the clean compressed air in housing w passes through flow hole A of body q , it is reduced to a specified pressure by the pressure reducing valve, and is discharged from the OUT. !

Min. 207 Panel 54 72.5 10 69.5 2 R1/8 74 40 7 30 OUT OUT IN 2 x M6 depth 10 2 x Rc1/4 Pressure gauge port Rc1/8 78 70 A 160

Facility having a small installation area (that can not vent the air naturally) Make a forced air exhaust vent on a wall at a high level and an air vent on a wall at a low level.

Facility having a small installation area (that can not vent the air naturally) Make a forced air exhaust vent on a wall at a high level and an air vent on a wall at a low level.

Bracket A (Part No.: ZS-50-A) Bracket B (Part No.: ZS-50-B) -15No.PS-OMV0009-E Mounting with orifice : Tighten the orifice to a torque of 1.50.1 Nm. Orifice (Part No.: ZS-48-A) -16No.PS-OMV0009-E Piping Piping specification: -02 and -N02 After hand tightening, tighten the fitting using a spanner on the flat surfaces of the fitting. The tightening torque must be 8 to 12 Nm.

Bracket A (Part No.: ZS-50-A) Bracket B (Part No.: ZS-50-B) -14No.PS-OMV0004-H Piping Piping specification: -02 and -N02 After hand tightening, tighten the fitting using a spanner on the flat surfaces of the fitting. The tightening torque must be 8 to 12 Nm. Piping specification: -F02 After hand tightening, tighten the fitting using a spanner on the flat surfaces of the fitting.

Rc C4SF-2J-A G C4SFF-2J-A NPT C4SFN-2J(Z)-A Rc C4SF-2-A G NPT C4SF-2(Z)-A Appearance and part No. -19- Option symbol 8 8J Semi-standard symbol Semi-standard: 8 Semi-standard: 8J Piping port thread ty pe (9) Part No. Piping port thread ty pe (9) Part No. Rc G NPT C4LF-8(Z)-A Rc C4LF-8J-A G C4LFF-8J-A NPT C4LFN-8J(Z)-A C4LF-8-A Appearance and part No.

Rc C3SF-2J-A G C3SFF-2J-A NPT C3SFN-2J(Z)-A Rc G NPT C3SF-2(Z)-A C3SF-2-A Appearance and part No. -16- Option symbol 8 8J Semi-standard symbol Semi-standard: 8J Semi-standard: 8 Piping port thread ty pe (9) Part No. Piping port thread ty pe (9) Part No. Rc C3LF-8J-A Rc C3LF-8-A G C3LFF-8J-A G NPT C3LFN-8J(Z)-A NPT C3LF-8(Z)-A Appearance and part No.

Suitable for slow operation of a rotary actuator. CC CC Integrate a converter and a valve unit in a compact configuration. Possible to select 4 types of valve units for applications. Possible to connect a converter and a valve unit independently. Wide range of series in terms of converter capacity and valve unit flow rate control capability.

To release residual pressure, select a model with a backflow function. Using a model without a backflow function makes for inconsistent residual pressure release (i.e., residual pressure may or may not be released) depending upon the operating conditions. 3.

To release residual pressure, select a model with a backflow function. Using a model without a backflow function makes for inconsistent residual pressure release (i.e., residual pressure may or may not be released) depending upon the operating conditions. 3.

Metric sizes Type 04 06 08 10 12 4 6 8 10 12 2 Elbow Control type 0 1 Meter-out Meter-in Port size M5 01 02 03 04 M5 x 0.8 1/8 1/4 3/8 1/2 With One-touch fitting Clean specifications Metal parts material Q G Brass (electoless nickel plated) Stainless steel 304 Needle Valve/Flow Characteristics AS121FP-M5 AS221FP-01 AS221FP-02 08,10 06,08 06 04 04 AS321FP-03 AS421FP-04 12 10 10,12 08 06 15

L F K M E J L Q Q A + Stroke B + Stroke A + Stroke B + Stroke W End Lock Mechanism Dimensions (mm) HN (Max.)