Solid State Auto Switch Do not connect wires while the power is on. Otherwise it can break the circuit inside the Auto switch causing malfunction. Do not lay wires or cables with power cable or high-voltage cable in the same wiring route.
Do not use the valves in an atmosphere having corrosive gases, chemicals, salt water, water, steam, or where there is direct contact with any of these. 2. Do not use in explosive atmospheres. 3. Do not use in locations subject to vibration or impact. 4. Do not use in locations where radiated heat will be received from nearby heat sources. 5.
Do not disassemble, modify, or repair the controller and its peripheral devices. 4. Do not put anything conductive or flammable inside of the controller. It may cause a fire. 5. Do not conduct an insulation resistance test or withstand voltage test on this product. 6. Ensure sufficient space for maintenance activities.
Do not carry the product by holding its cables. It may cause an injury or damage to the product. 5. Do not connect power or high-voltage cables in the same wiring path as the unit.
Do not stare into beam visible at XF1/2.
Do not drop or bump. Do not drop, bump, or apply excessive impacts (300 m/s2 or more for reed switches and 1000 m/s2 or more for solid state switches) while handling. Although the body of the switch may not be damaged, the inside of the switch could be damaged and cause a malfunction. 2. Do not carry a cylinder by the auto switch lead wires. Never carry a cylinder by its lead wires.
Modes and setting items 14 7-1-1. Mode types and functions 14 7-1-2. Mode switching procedure 14 7-1-3. Setting of function mode 15 7-1-4. Data setting range 16 7-2. Setting 17 7-3. Counter operation 21 7-3-1. Handling data range 21 7-3-2. Reset and hold input 21 7-3-3. Correspondence of banks and bank terminals at switching 21 7-3-4.
Do not use until you can verify that equipment can operate properly. Verify correct mounting by suitable function and leakage inspections after air and power are connected following mounting, maintenance or conversions. 2. Do not drop or bump. Do not drop, bump or apply excessive impact (1000 m/s2) when handling.
This may shorten the pump life. 14. If clear water is used, it should satisfy the quality standards shown below.
Do not apply any impact when you load the cylinder in the locked position.
RR1 RR1 E1 L1 MM A A1 U1 NDH10 NX +0.058 0 +0.058 0 +0.058 0 0.2 0.4 0.2 0.4 0.3 0.5 0.4 0.2 0.4 0.2 0.5 0.3 +0.058 0 +0.058 0 +0.058 0 16 20 22 I-G02 I-G03 I-G04 16 34 41 42 8.5 10.5 14 25 30 30 M8 x 1.25 10.3 12.8 12 11.5 14 14 20 25, 32 40 8 10 10 8 10 18 Y-G02 20 8.5 25 30 30 M8 x 1.25 10.3 12.8 12 16 20 36 21 IY-G02 IY-G03 IY-G04 34 41 42 11.5 14 14 8 8 20 M10 x 1.25 Y-G03 25, 32 40
Female Connector: KQ2F H (width across flats) 14 17 14 17 19 14 17 19 17 19 Applicable tubing O.D.
D1 D2 L1 L2 M 15 23 15 22 25 17 24 24 27 30 36 31 52 59 58 KQ2F04-01 KQ2F04-02 KQ2F06-01 KQ2F06-02 KQ2F06-03 KQ2F08-01 KQ2F08-02 KQ2F08-03 KQ2F10-02 KQ2F10-03 KQ2F12-02 KQ2F12-03 KQ2F12-04 KQ2F16-03 KQ2F16-04 1 8 1 4 1 8 1 4 3 8 10 27 31 27.5 31 33.5 29 32.5 33.5 34.5 36.5 35 37 41 38 43 11 16 5.6 4 14 17 14 17 19 14 17 19 17 19 4 14 11 13 15 11 13 14 14 15 13.1 10.4 17 12 6 1 8 KQ2F16 26.1
Safety Instructions Warning Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use.
Do not use the valves in an atmosphere having corrosive gases, chemicals, salt water, water, steam, or where there is direct contact with any of these. 2. Do not use in explosive atmospheres. 3. Do not use in locations subject to vibration or impact. 4. Do not use in locations where radiated heat will be received from nearby heat sources. 5.
N.O. 2-port 7 MPa 59 14 19 63 19 61 3 MPa 7 MPa 3 MPa 7 MPa 52 59 52 59 71 56 59 56 59 71 79 55 17 14 17 14 7 7 14 7 14 7 9 9 22 19 22 19 12 12 19 12 19 12 15 15 56 63 56 63 75 60 63 60 63 75 83 59 22 19 22 19 12 12 19 12 19 12 15 15 54 61 54 61 73 58 61 58 61 73 81 57 SGH200 3-port 3-port dual pressure type N.C.
A A1 E1 L1 MM RR1 U1 NZ L CNS 42 56 16 20 22 28 30 40 M14 x 1.5 M18 x 1.5 12 16 14 20 I-G04 I-G05 Y-G04 Y-G05 +0.5 +0.3 42 56 14 18 22 28 30 40 M14 x 1.5 M18 x 1.5 12 16 14 20 36 41.6 +0.058 0 -0.3 -0.5 +0.058 0 +0.5 +0.3 44 50.6 +0.070 0 Knuckle pin and snap ring are included. -0.3 -0.5 +0.070 0 CLS CLQ MLGP Knuckle Pin (Common with double clevis pin) Rod End Nut RLQ MLU d d Dd9 ML1C C m
Do not apply excessive lateral loads to the piston rod.
Do not Do not use in an atmosphere containing flammable or explosive gases. Fire or an explosion can result. The product is not designed to be explosion proof. Do not Do not use the product for flammable or highly permeable fluids. Fire, explosion, breakage or corrosion can result. Do not Do not use the product in a place where static electricity is a problem.