16 20 25 32 36 46 60 70 16 20 25 32 36 46 16 20 25 32 36 46 17 20 20 12 12 17 17 20 20 27 27 12 12 17 17 20 20 22 22 22 22 30 30 56 65 73 36 40 48 56 65 73 92 103 36 40 48 56 65 73 36 40 48 56 65 73 4 x M12 x 1.75 4 x M16 x 2 4 x M16 x 2 0 50 342 87 435 255 100 56 4.6 106 150 4 x M10 x 1.5 23 40 (1 1/2B) 50 (2B) 0 60 450 94 545 356 120 70 6.4 120 155 4 x M12 x 1.75 28 0 219 62
W : Mass (kg) F : Load (N) FE : Load equivalent to impact (when stopper collides) (N) a : Average speed (mm/s) M : Static moment (Nm) : Collision speed (mm/s) L1 : Distance to the center of load gravity (m) ME : Dynamic moment (Nm) g : Gravitational acceleration (9.8 m/s2) At impact: = 1.4 a 1.4 100 = 1.4 a (mm/s) FE = agW Note 4) ME = FEL1 = 0.05 agWL1 (Nm) 1 3 Note 4) Average load coefficient
If there is an offset in the L2 direction, an eccentric load will be applied to the guide. In this case, pressing operations should not be performed.
1 s/2 s Output protection Output mode Response time Note 6) Voltage output Current output Short circuit protection Flow rate Select from hysteresis mode, window comparator mode, accumulated output mode, or accumulated pulse output mode. 0.5 s/1 s/2 s (linked with the switch output) Voltage output: 1 to 5 V Output impedance: 1 k7 Analog output Output current: 4 to 20 mA Max. load impedance
An injury or failure can result. 1. Pay attention to the length of time that a switch is ON at an intermediate stroke position.
Never use in an atmosphere of explosive gases. The construction of auto switches is not intended to prevent explosion. Never use in an atmosphere with an explosive gas since this may cause a serious explosion. 2. Do not use in an area where a magnetic field is generated. Auto switches will malfunction or magnets inside actuators will become demagnetized. 3.
To operate a relay as a load, use the relay shown in the table below or the equivalent, in order to extend the life of the switch. qWhen handling the product, do not drop an object on it, gouge it, or apply an excessive impact on it. wDo not operate it in an area in which a large amount of magnetism is present.
PNP open collector 2 output + Analogue output Max. 80 mA Residual voltage: 1.5 V or less Bracket A (Part No.: ZS-46-A1) Bracket B (Part No.: ZS-46-A2) DANGER indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury.
If using the product in an interlocking circuit: Provide a double interlocking system, for example a mechanical system Check the product regularly for proper operation Otherwise malfunction can result, causing an accident.
Baud rate Max. bus cable length 1 Mbit/s 25 m 800 kbit/s 50 m 500 kbit/s 100 m 250 kbit/s 250 m 125 kbit/s 500 m 50 kbit/s 1000 m 20 kbit/s 2000 m 10 kbit/s 5000 m -10No.EX-OMK0006-C Bus cable and termination resistors The cables, connectors, and termination resistors used in CANopen networks shall meet the requirements defined in ISO 11898.
Do not use the air cylinder as an air-hydro cylinder. The use of turbine oil as a fluid for an air cylinder may result in oil leakage. 4. The oil stuck to the cylinder is grease. 5. The base oil of the grease may seep out.
www.stevenengineering.com I 6.13 VACUUM VACUUM PADS SERIES ZP F L AT T Y P E F L AT W I T H R I B Y D I M E N S I O N S PA D D I A M E T E R S 10, 13, 16 Model A B C D E F G H I Flat Flat with Rib ZPR10 U C 10 12 12 21 29.9 46 57 80 91 3 1.7 ZPR13 U C 13 15 12 21 29.9 46 57 80 91 3 1.8 ZPR16 U C 16 18 12.5 21.5 30.4 46.5 57.5 80.5 91.5 3.5 1.2 D E E P T Y P E D I M E N S I O N S PA D D I
If using the product in an interlocking circuit: Provide a double interlocking system, for example a mechanical system Check the product regularly for proper operation Otherwise malfunction can result, causing an accident.
to 1000 mm/s (Refer to page 10-5-7.) (3) Piston speed H (High speed/High frequency type) 5 mm/s to 3000 mm/s (Refer to page 10-5-7.)
to 1000 mm/s (Refer to page 10-5-7.) (3) Piston speed H (High speed/High frequency type) 5 mm/s to 3000 mm/s (Refer to page 10-5-7.)
An injury or failure can result. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use. Do not operate in an atmosphere containing flammable or explosive gases. Fire or an explosion can result. This product is not designed to be explosion proof.
Dimensions (mm) Grommet: G Conduit: C DIN terminal: D Conduit terminal: T P Port size B D E F H K L M N A C Model Note) Q V R Q R Q R S Q R S U 22 23 45 44 43 58 40.5 46.5 99 43 66 83 13.5 28 31 56.5 12.5 28 14 12.8 M4 4.5 64 1/8 VCL21 22 23 46 44 44 58 41.5 46.5 99 44 66 86 18 36 31 58.5 12.5 28 18 12.8 M4 6 67.5 1/4 24 25 56.5 46 54.5 60 52 48.5 101 54.5 68 99 22 40 36.5 11 15 32 20 19
Furthermore, it cannot be used as an emergency cutoff valve.
RZQ MI W S CEP1 CE1 < For AC > (Since the rectifier prevents the production of surge voltage, there is no S type.)