NCA1 Male threads 17 : 3/8-16 45 : 2-12 78 : M18 x 1.5 cannot be specified equal to, but 18 : 3/8-24 46 : 2 1/4-12 79 : M18 x 2.5 19 : 7/16-14 47 : 1 7/8-12 80 : M20 x 2.0 not, greater than the rod diame20 : 7/16-20 48 : 2 3/4-12 81 : M20 x 2.5 ters as standard. 21 : 1/2-13 49 : 3-12 82 : M22 x 1.5 22 : 1/2-20 50 : 3 1/4-12 83 : M22 x 2.5 23 : 9/16-12 51 : 3 1/2-12 84 : M24 x 2.0 24 : 9/16-18
An application which could have negative effects on people, property, or animals requiring special safety analysis. 4. Use in an interlock circuit, which requires the provision of double interlock for possible failure by using a mechanical protective function, and periodical checks to confirm proper operation. 1.
When a load directly connected to the cylinder is stopped at an intermediate position: Apply the operating range in the catalog only in these cases where the stopper cylinder is used to stop pallets on a conveyor belt. When using the stopper cylinder to stop loads directly connected to a cylinder or some other equipment, a lateral load is applied as the cylinder thrust.
When a load directly connected to the cylinder is stopped at an intermediate position: Apply the operating range in the catalog only in these cases where the stopper cylinder is used to stop pallets on a conveyor belt. When using the stopper cylinder to stop loads directly connected to a cylinder or some other equipment, a lateral load is applied as the cylinder thrust.
Secure the switch at an appropriate position with a flat head watchmakers screwdriver as indicated in Figure (3). MRHQ Tightening torque: 0.05 to 0.1 Nm Misc. Second groove MRHQ10/16 D3. Install the switch case, with a switch attached securely in the hole, in the direction indicated in Figure (1). 20Figure (3) Figure (1) 12-11-19 Selection Maintenance Caution Warning 1.
As a rough guide, tighten the screw an additional 90 after feeling a tighten resistance. When auto switch D-Y69 A is used B L Auto Switch Hysteresis Auto switches have a differential like a micro switch. Plesae refer to the following table as a guide when setting auto switch positions.
In such cases, use a dual pressure control circuit as a pneumatic circuit. Maximum tightening torque (Nm) L (mm) Model Bolt M8 x 1.25 MGF40 18 8 M10 x 1.5 MGF63 36 10 M12 x 1.75 MGF100 65 10 847
These models are designed to decelerate medium-to-large loadsLow Ranqe (LROEM) models are available to control velocities as low as 3 in./sec. and propelling foircei as high as 4,800 lbs. (21,000N). They are fully field repairable.
Set the operating pressure using the graphs as a guide.
A 0.6 16 Do not operate with the stroke adjusting unit fixed in an intermediate position. When the stroke adjusting unit is fixed in an intermediate position, slippage can occur depending on the amount of energy released at the time of an impact. In such cases, the use of the adjusting bolt mounting brackets, available per made-toorder specifications -X416 and -X417, is recommended.
A 0.6 16 Do not operate with the stroke adjusting unit fixed in an intermediate position. When the stroke adjusting unit is fixed in an intermediate position, slippage can occur depending on the amount of energy released at the time of an impact. In such cases, the use of the adjusting bolt mounting brackets, available per made-toorder specifications -X416 and -X417, is recommended.
Operating Range (mm) Bore size Switch types 25 32 20 D-A9, D-A9V D-F9, D-F9V D-F9W, D-F9WV 11 12.5 14 6.5 7 7 Values in this table include hysteresis and are to be used as a guide only. They do not guarantee an actual fixed range (expect approximately 30% dispersion).
Then, give an additional half rotation of screw. After that, incline the lever by 90 and confirm that the indicator light is not on and does not show either red or green.
When the SET button is pressed continuously for 4 seconds or more, the display changes as shown in .
Throttle speed controller, such as Series AS, is recommended for speed adjustment.
Lightning surge countermeasures should be applied directly to system components as necessary. 2. The pressure sensors do not have an explosion proof rating. Never use pressure sensors in the presence of flammable or explosive gases.
This produces an air cushion cylinder which retains the merits of a compact design. Nearly three times the allowable kinetic energy Interchangeable mounting The mounting dimension "M" is the same as the compact cylinder Series CQS/CQ2. Working principle A + A' A' q When the piston is retracting, exhaust is discharged from both A and A' until piston seal H passes the air passage A.
When transporting in an upward direction, factors such as acceleration, wind pressure and impact force must be considered in addition to the workpiece weight. Use caution particularly when lifting items such as glass plates and circuit boards, because a large force will be applied by wind pressure.