Low Differential Pressure Sensor When a surge generating a load such as a relay or solenoid is directly driven, use a type of switch with a built-in surge absorbing element. 4. Since the type of fluid varies depending on the product, be sure to verify the specifications. The switches do not have an explosion proof rating. To prevent a possible fire hazard, do not use with flammable gases or fluids. 5.
.: ZS-31-B) 5000 (38.6) Brown 45 2: White 1: Brown 30 White 15 Blue 4: Black 3: Blue Black M12 (Part no.: ZS-31-C) (31) 5000 Brown 45 23.5 When used as a switch output device 30 White No.
lrlA |.25N/A r{/A.1 3 .35 t ( l{/A 13.9 or.
It can also be used as a negative common.
Affix a safety cover in places where there is a danger of personal injury. 4. Make sure that the offset of the clamping position is within 15 mm as shown in the figure below. A large gripping force is generated during clamping. If there is a possible pinching hazard, design the structure to avoid contact with the human body. Allowable offset 15 mm Caution 1.
46 F 33 34 34 H 24 25 25 J 30 40 40 D 22 24 24 A 40 44 44 B 20 22 22 C 9 10 10 Model VVX31 VVX32 VVX33 TI/ TIL PA PAX PB 17-3-91
Avoid especially the application of pressure above specifications through a water hammer.
Note 2) As the stroke increases, more sliding resistance may result due to the deflection of the piston rod and other factors. Take measures such as the installation of a guide. 10-4-10 11 Smooth Cylinder Series CM2Y Dimensions/20 to 40 Mounting bracket dimensions are the same as those of the standards, double acting, single rod type of Series CM2.
Note 2) As the stroke increases, more sliding resistance may result due to the deflection of the piston rod and other factors. Take measures such as the installation of a guide. 10-4-10 11 Smooth Cylinder Series CM2Y Dimensions/20 to 40 Mounting bracket dimensions are the same as those of the standards, double acting, single rod type of Series CM2.
It is important to understand that one may follow this guides recommendation, yet have a failure due to a parameter specic to the given application, as noted.
When it reaches , the head pressure (PH) rises quickly as indicated by the line from to . Therefore, there is no time loss associated with the pressure transmission lag indicated by the line from to , as in the case of meter-in control that is effected through the use of a speed controller.
Keep wiring as short as possible to prevent interference from electromagnetic noise and surge voltage. Do not use a lead wire longer than 30 m. Wire the DC (-) line (blue) as close as possible to the power supply. Operating environment Do not use the product in an environment where the product is constantly exposed to water or oil splashes. Otherwise it can cause failure or malfunction.
(In cases where there is a gasket in two places such as a universal elbow or universal tee, double the additional tightening to 1/2 turn.) 5.
Orifice Fittings Many of our small brass fittings such as B1, B2, T1, T2, etc., are available as orifice fittings. In the case of Tees, the branch and/or one end of the run may be an orifice. A cross can have as many as three orifices. The general dimensions in this catalog are subject to change without notice 5/32 Couplings 7/16 1/2 15/16 1 5/16 5/16 Typ.
Set the operating pressure using the graphs as a guide.
Uni thread fittings 1) First, tighten the threaded portion by hand, then use a proper wrench, which could be suitable for the width across flats of the hexagon body, to tighten it further at a wrench tightening angle shown below. As a reference value for the tightening torque, refer to the table below.
In the case of common exhaust type, exhaust air from both sides of R port as well. A port size Symbol Port size Exhaust style Individual exhaust Common exhaust 01 1 8
Use 0.3 to 0.7 times the thrust (differs depending on the operating speed) as a guide for actual use. g: Gravitational acceleration Dynamic Moment M1 Mounting orientation Dynamic load FE Horizontal Ceiling Wall Vertical Z a 1.4a x x mn x g a 1 3 x FE x Z M1E Dynamic moment Dynamic moment M2E is not generated.
Use as short a wire as possible. Using a long wire to reach the load could increase the inrush current when the switch is on and consequently shorten the switch life. 3. Use a contact protection box for auto switches without a contact protection circuit or that have induction loads with 5 meters or more length lead wires.