Booster Regulator/Air Tank

ARJ AR425 to 935 Air-operated type Pilot pressure VBA11A VBA10A, 20A, 40A, 43A ARX Drive chamber A Governor Drive chamber A Governor Drive chamber B Booster chamber A AMR IN (Inlet) IN (Inlet) Drive chamber B ARM VBA22A, 42A Piston rod Piston rod ARP Booster chamber A IR-A Piston Piston IR Check valve Booster chamber B Booster chamber B Check valve IRV Switching valve Switching valve E OUT

ARJ310

When used with a closed downstream circuit and balance circuit Contact SMC as there are cases where the regulator cannot be used. 5. Perform downstream pressure setting in a range that is 85% or less of the supply pressure. However, the setting should be within the regulating pressure range. 6.

Air Suction Filter With One-touch Fittings

Applicable Element size Element O-ring filter model mm for cover I-34S-A ZFB10 10 x 6 x L33 10 pcs. 10 pcs. I-35S-A ZFB20 12 x 8 x L42 10 pcs. 10 pcs. I-36S-A ZFB30 14 x 10 x L45 10 pcs. 10 pcs. I-39S-A ZFA401 16 x 14 x L60 10 pcs. 10 pcs. -9- < Element Replacement > 1. Stop the operation and reduce the internal pressure of the filter to atmospheric pressure. 2.

Process Pump Series PA3000/5000/PAX1000 Series PB1000

Since a large quantity of liquid will be pumped out, use a suitable throttle in the discharge port if problems occur. Note 3) With a low number of operating cycles, even a valve with a small Cv factor can be operated.

Process Pump Series PA3000/5000/PAX1000 Series PB1000

Since a large quantity of liquid will be pumped out, use a suitable throttle in the discharge port if problems occur. Note 3) With a low number of operating cycles, even a valve with a small Cv factor can be operated.

2-Apr-01 Quick Reference Auto Switch Chart with (PnP) M-8 (3 pin) & M-12 (4 pin) Connectors, Page 1/2 32, 40, 50, 63, 80 & 100 Bore sizes (Auto Switch Spacer # BMP1-032 required) 32, 40, 50, 63, 80, 100, 125 & 200 Gripper Bore sizes (sizes depend on seri

If driving a load such as a relay that generates a surge voltage, use a switch with a built-in contact protection circuit or use a contact protection box. 1) For an auto switch without a contact protection circuit, use a contact protection box when the wire length is 50m or longer.

IIIIIIIIII

This is accomplished by interfacing a stepping motor and gear box to a modified 800 or 900 series subminiature regulators. A calibration report included with every unit provides a detailed test data including a scale factor that corresponds to a slope that will yield a open loop accuracy including linearity, repeatability and hysteresis, of < +/3% FS.

Pressure Relief 3 Port Valve with Locking Holes VHS20/30/40/50

Port size Body size Thread size Port thread Symbol N F Rc NPT G 01 02 03 04 06 10 1/8 1/4 3/8 1/2 3/4 1 An interface part is required if a spacer or spacer with bracket shown in the table below is attached to a modular FRL.

Exhaust Cleaner Series AMC

U S T C L E A N E R S E R I E S (N)AMC 0 (N)AMC Japanese N North American O P T I O N B Bracket D Threaded Drain Port (Female) B O D Y S I Z E P O R T S I Z E 2 1/4 3 3/8 5 3/4 6 1 8 1 1/2 9 2 02 1/4 03 3/8 04 1/2 06 3/4 10 1 14 1 1/2 20 2 T H R E A D T H R E A D 1 Male 2 Female (Only NAMC220, 320, 520 Special Order Only) R(PT)* Remove (N) when ordering N NPT FOR FURTHER TECHNICAL DETAILS

VZM500

(Except push-pull) Note 2) For push button (mushroom), push button (extended), push button (flush) and a single unit of fastening ring, refer to pages 5-6-6 to 5-6-7. The other parts are not replaceable.

Speed Controller with Pilot Check Valve with One-touch Fitting Series ASP 1

(Refer to pages 15-6-3 and 15-6-5 for details.)

Silencer 40 dB (A): High Noise Reduction Type Series ANA1

Silencer 40 dB (A): High Noise Reduction Type Series ANA1 Model (Screw-in connection) A high noise reduction type silencer keeps the noise level inside a plant below 85 dB (A).

Speed Exhaust Controller Series ASV Size: M3, M5, 1/8, 1/4, 3/8 1

M1 Weight (g) ASV120F-M3-04 ASV220F-M5-04 ASV220F-M5-06 Model 5 8 9 M3 x 0.5 M5 x 0.8 M5 x 0.8 5.5 8 8 9.3 9.3 11.6 7.2 9.6 9.6 21.4 22.8 23.6 25 27.6 28.4 9.8 11.1 11.1 28.6 31.4 31.4 26.1 28.6 28.6 25.8 27.7 27.7 23.3 24.9 24.9 12.7 12.7 13.5 4 4 6 Reference dimensions of M thread after installation. Inch Size Applicable tubing O.D. d T H D1 D2 L1 L2 L3 L4 A Max. Min. Max. Min.

Part Number Description: BOWL ASSEMBLY (AL40/50/60)   Product Line: E   Product Line Description: AIRLINE EQUIPMENT   Family Code: 182   Family Description: AL MASS PRO   Class Code: 21   Click here to report information errorImage shown may not match exact part number

Part Number Description: BOWL ASSEMBLY (AL40/50/60)   Product Line: E   Product Line Description: AIRLINE EQUIPMENT   Click here to report information errorImage shown may not match exact part number

BOWL ASSEMBLY (AL40/50/60)

BOWL ASSEMBLY (AL40), AIRLINE EQUIPMENT, AL MASS PRO, 21, AL MASS PRO NO SIZE RATING, 0.07348 lb

BOWL, ASSEMBLY (AL40/50/60), AIRLINE EQUIPMENT, AL MASS PRO, 21, AL MASS PRO NO SIZE RATING, 0.737 lb

BOWL ASSEMBLY (AL40/50/60), AIRLINE EQUIPMENT, AL MASS PRO, 21, AL MASS PRO NO SIZE RATING, 0.4884 lb

Part Number Description: BOWL ASSEMBLY (AL40/50/60)   Product Line: E   Product Line Description: AIRLINE EQUIPMENT   Family Code: 184   Family Description: AW MASS PRO   Class Code: 21   Part Code: 2   Reference Code:  J   Click here to report information errorImage shown may not match exact part number