pa Use a 3 wire switch if this specification will not be satisfied. Moreover, leakage current flow to the load will be "n" times larger when "n" auto switches are connected in parallel. 24 Series MNB Auto Switch Precautions 2 Be sure to read before handling.
Warranted repair shall be on request basis. Unrequited repair shall be provided in accordance with the warranty period, preconditions and terms defined above. Therefore, the repair service shall be available on a chargeable basis if a failure is detected after the warranty period.
range is 1.0 to 1.5 MPa, the pressure characteristics will be 5% F.S.
Warranted repair shall be on request basis. Unrequited repair shall be provided in accordance with the warranty period, preconditions and terms defined above.
Cylinder with Lock 32, 40, 50, 63, 80, 100 Hexagon wrench Lock can be manually operated with a hexagon wrench. Maintaining a manual lock released state Locked state Can be easily mounted onto equipment The lock unit and the cylinder can be separated.
The switch may be damaged if a screw other than the one supplied, is used.
Please take note that warranted repair shall not be available if these preconditions are disregarded. (1) System operation shall be conducted by following operating procedure defined in the Operation Manual. (2) Daily and periodic inspections designated in the Operation Manual shall be made as scheduled. (3) Inspection record shall be entered in the Daily Inspection Sheet provided in the
The suppressor residual leakage voltage should be as follows. 4.
To use the lock for drop prevention purposes, the load to be attached to the cylinder must be within 35% of the cylinders holding force.
To use the lock for drop prevention purposes, the load to be attached to the cylinder must be within 35% of the cylinders holding force.
1 Be sure to read this before handling the products.
Extended periods of continuous energization Contact SMC if valves will be continuously energized for extended periods of time. Caution 1. Momentary energization If a double solenoid valve will be operated with momentary energization, it should be energized for at least 0.1 second. 2.
KBC1 KBC2 KBC3 KBC4 KBP1 KBP2 KBP3 KBP4 KBN2 KBV1-06 KBE2-06 KBV2-06 5 Kl Bracket: KBX (P.2.1-80) Component module KBV2-061 KBV1-061 KBR2-11 KBH2-R2S1 KBP1 1 KBP1 KB X 6 Ml KBR2-1 Hl Applicable thread size KBH2-R2R Dl KBV2-06 KBP1 Style MS Bracket: KBX KBV1-06 Component module KBV2-061 KBV1-061 KBR2-11 KBH2-R2S1 KBP2 1 KBP1 1 Tl Part No.
Even within a given allowable kinetic energy level, there is an upper limit to the size of the load that can be sustained. Thus, a horizontally mounted cylinder must be operated below the solid line, and a vertically mounted cylinder must be operated below the dotted line.
Be especially careful of the center trunnion style. (Refer to pages 25 and 26 for details.)
The tightening torque should be approximately 0.05 to 0.15Nm.
The instruction manual should be carefully read and fully understood before the product is installed and operated. Also, the manual should be kept where it can be easily referred to at any time. 2. Allow space for maintenance. Allow the space necessary for maintenance and inspections. 3. Tighten screws with the proper tightening torque.
Avoid applications in which two or more end lock cylinders are synchronized to move one workpiece, as one of the cylinder locks may not be able to release when required. 6. Use a speed controller with meter-out control. Lock cannot be released occasionally by meter-in control. 7. Be sure to operate completely to the cylinder stroke end on the side with the lock.