IBV-OMY0015 Do not use in an environment where corrosive gases, chemicals, sea water, water or steam are present. 2. If using in a location directly exposed to sunlight, shade the product from the sunlight. 3. Do not mount the product in locations where it is exposed to radiant heat. 9 4. Do not use the product in a place where static electricity is a problem.
Do not drop or bump. Do not drop, bump, or apply excessive impacts (300 m/s2 or more for reed switches and 1000 m/s2 or more for solid state switches) while handling. Although the body of the switch may not be damaged, the inside of the switch could be damaged and cause a malfunction. 2. Do not carry a cylinder by the auto switch lead wires. Never carry a cylinder by its lead wires.
Do not use the drain tube in an upward direction. Do not bend or crush the drain tube. (Operation of auto drain will stop and water will flow out through the air outlet.) When tightening piping at the air inlet/outlet tube, the nozzle should be held firmly with a pipe wrench.
Do not use in these conditions. (Refer to specifications.) Consult SMC if a fluid other than compressed air is used. 2.
Wrapping of sealant tape When screwing together pipes and fittings, etc., be certain that chips from the pipe threads and sealant material do not get inside the piping. Also, when sealant tape is used, leave 1.5 to 2 thread ridges exposed at the end of the threads. Operating Environment Warning 1. Do not use in environments where there is a danger of corrosion.
Therefore, do not use it with or expose it to the following chemicals: paint thinner, carbon tetrachloride, chloroform, acetic ester, aniline, cyclohexane, trichloroethylene, sulfuric acid, lactic acid, watersoluble cutting oil (alkalinic), etc. 2. Do not expose it to direct sunlight.
Do not disassemble the product because it may damage the air cushion mechanism.
Do not operate with anything other than compressed air. The cleaning equipment has been designed to be used only with compressed air. To use fluids instead of compressed air, please contact SMC beforehand. 2. Do not use compressed air that contains chemicals, organic solvents, salt, or corrosive gases.
Do not use the product in applications where excessive external force (including vibration) or impact force is applied to it. Do not apply impact and vibration outside of the specifications; it may lead to a malfunction.
Do not connect black. Power supply/output connection lead wire Cable Specifications Pin no.
Do not use the auto drain valve in such environment.
Do not put the heavy objects on the products. Do not use the products as scaffold. 2. Do not use the products in conditions that do not meet the product specications. Product Returns When returning the product to SMC, make sure to properly purge to remove all hazardous materials and return the product complying with SMC specied procedures.
Do not operate in environments with corrosive gases, chemicals, sea water, fresh water or water vapor, or where there will be contact with the same. 2. In locations exposed to direct sunlight, block the sunlight. 3. Do not operate in locations where vibration or impact occurs. 4. Do not operate in a location near a heat source where radiated heat will be received. Pressure gauge 1.
Do not use in these conditions. (Refer to specifications.) 2. Do not use for power transmission These products are not designed to be used as bearings for transmitting power from a drive source, such as a motor. Such use may lead to rotation faults, or damage. Piping Caution 1.
Do not disassemble or modify the main unit. Operating Environment Warning Caution 1. Do not use in the following environments, as this can cause damage and reduced performance. 1. Do not step on or place heavy objects on the unit. 1. Locations with an atmosphere of corrosive gases, organic solvents or chemical solutions, and locations where there may be contact with the same. 2.
Do not use in atmospheres contacting corrosive gases, chemicals, sea water, water, water steam, or where there is direct contact with any of these. 2. Do not use in explosive atmosphere. 3. Do not use in locations subject to vibration or impact. 4. Do not expose to direct sunlight for an extended period of time. Protective cover should be used to shield. 5.
Do not remove any name plate or label. Do not drop, hit or apply an excessive shock to the unit. Follow the specified tightening torque. Do not apply any excessive force to cables by repeated bending, tensioning or placing a heavy object on the cables. Connect wires and cables correctly. Do not perform any wiring work while the power is on.
Do not put the heavy objects on the products. Do not use the products as scaffold. 2. Do not use the products in conditions that do not meet the product specications. Product Returns When returning the product to SMC, make sure to properly purge to remove all hazardous materials and return the product complying with SMC specied procedures.
Do not expose the product to direct sunlight for an extended period of time. 3. Do not use in a place subject to heavy vibrations and/or shocks. 4. Do not mount the product in locations where it is exposed to radiant heat.
Do not use valves in atmospheres of corrosive gases, chemicals, salt water, water or steam, or where there is direct contact with same. 2. Do not use in an explosive atmosphere. 3. Do not use in locations subject to vibration or impact. 4. Do not use in a location where radiated heat will be received from a heat source in the vicinity. 5.