Speed Controller for Low Speed Operation with One-touch Fitting Series AS-FM Elbow Type/Universal Type (Resin Body) 1 T D2 L1 D2 L1 L2 L2 AS ASP Metric Size ASN A M1 L5 Max.
No code M V X 4) PTFE recommended for applications such as within a process tool. 5) Not available with SH material.
Auto switch model Bore size [mm] 20 25 32 40 D-M9m(V) D-M9mW(V) BM8-020 (A set of a, b, c, d) BM8-025 (A set of a, b, c, d) BM8-032 (A set of a, b, c, d) BM8-040 (A set of a, b, c, d) BM8-025S (A set of a, b, c, d) * S: Stainless steel set screw BM8-032S (A set of a, b, c, d) * S: Stainless steel set screw BM8-040S (A set of a, b, c, d) * S: Stainless steel set screw D-M9mA(V) BM8-020S (A
With the expansion of its international network, SMC has earned a solid reputation as reliable international brand, and has exceeded the goal of 20% global market share.
Lower or raise supply pressure a little at a time, and use in a supply pressure range where the intermittent noise does not occur. Clogging of the silencer Replace the silencer. Add a filter to supply (compressed) air circuit. Clean the mesh periodically as necessary by washing, air blow and so on or replacing plate B. Refer to 7.2 Maintenance for suction cup.
steel 25, 32 only 55 19 Steel ball A Carbon steel Cushion seal A Urethane 56 20 Same as cushion seal A except for 20, 25 standard strokes Steel ball B Carbon steel 21 Cushion seal B Urethane 57 Tooth ring Stainless steel 22 Damper Urethane Cushion ring gasket A NBR 58 23 Same as cushion ring gasket A except for 20, 25 standard strokes C type snap ring for taper ring Carbon steel 24 Cushion
Noise Level Sound level Noise level reference Sound example 20 dB Whisper The sound of leaves touching each other or the sound of snow falling Suburbs late at night or the sound of writing with a pencil 30 dB Very quiet 40 dB A quiet residential area in the daytime or in the library HEF002 Noise level range External unit of a home air conditioner (close distance) or in a quiet office 50 dB
The poppet valve has a pressure balancing mechanism in which A port pressure is constantly applied from the back and the center spring is acting as a backup.
As viewed from the end of the rod, the pin is tilted 15 to the left of the center. 3. Supply an air pressure of 0.3 MPa or more to the unlocking port. 4. Rotate the pin 30 to the right with a wooden implement such as the grip of a wooden hammer or a resin stick without scratching.
Note 2) The dimensions (A + stroke) and (B + stroke) for 10 mm stroke will be the same as those for 15 mm stroke.
Port 2 (A) pressure (MPa) Port 2 (A) pressure (MPa) 0.8 0.8 0.8 0.7 0.7 0.7 0.6 0.6 0.6 0.5 0.5 0.5 0.4 0.4 0.4 0.3 0.3 0.3 0.2 0.2 0.2 0.1 0.1 0.1 VY1D00-5 VY1B0-5 VY120-5 1 0 1 2 3 4 5 0 1 2 3 4 5 V V V 0 1 2 3 4 5 A VY1D00-6 VY1B0-6 VY120-6 A 1 1 1 1 0 2.5 5 7.5 10 0 2.5 5 7.5 10 V V V 0 2.5 5 7.5 10 VY1D00-7 VY1B0-7 VY120-7 1 A 4 0 8 12 16 20 mA 4 0 8 12 16 20 mA 4 0 8 12 16 20 mA 2 2
Use 0.3 to 0.7 times the thrust (differs depending on the operating speed) as a guide for actual use. g: Gravitational acceleration Dynamic Moment M1 Mounting orientation Dynamic load FE Horizontal Ceiling Wall Vertical Z a 1.4a x x mn x g a 1 3 x FE x Z M1E Dynamic moment Dynamic moment M2E is not generated.
As a rule, it should be turned about 90 past the point at which tightening can be felt.
Use this as a guideline purpose only for model selection because the value varies depending on the material and/or size of a subject.
The proper tightening torque for pipe fittings is as shown in the table. As a rule, they should be tightened 2 to 3 turns with a tool after first tightening by hand. Be careful not to cause damage by over-tightening. Note) Use Series AS-F with -X214 for the throttle valve.
Through the availability of a wide range of series in terms of converter capacity and valve unit flow rate control capability, speed as high as 200 mm/s (throttle valve) can be achieved with a 80 cylinder.
If a magnetic substance is closer than 2.5mm, auto switches may malfunction due to a drop in magnetic force. If this surface is to be used for mounting, a spacer composed of a nonmagnetic substance (aluminum, etc.) is required as shown in the figure below.
*Loctite 542 (medium strength) or equivalent 2.50 or larger bore size cylinders cannot be dis-as-sembled. When disassembling cylinders with bore sizes of 20 through 40, grip the double flat part of either the head cover or the rod cover with a vise and loosen the other side with a wrench or a monkey wrench, etc., and then remove the cover.
Note 2) Allowable rotating torque, and operating range when used as a lifter, are the same as MGPWL series.
Pressure (including vacuum) holding It is not usable for an application such as holding the pressure (including vacuum) inside of a pressure vessel because air leakage is entailed in a valve. 8. When the conduit type is used as equivalent to an IP65 enclosure, install a wiring conduit, etc. 9.