Air Cylinder NCQ7 Series Compact Cylinder N4-18 NCQ2, Series NCQT 200 PSI (14 kgf/cm') -20-150.F (-25 -65"C) 2 20 inch/sec (50-500mm/sec) FEATURES 1) The NCQT Series cylinder gives a shorter, lighter and more compact package for a given stroke. 2) The unique shape enables the use of rail-mounted switches without significantly increasing the overall length. .
Lead wire length symbols 0.5m Nil (Example) Y59A 3m L (Example) Y59AL 5m Z (Example) Y59AZ Solid state switches marked with a "" are produced upon receipt of order.
NPT, R1/8 3 to 5 NPT, R1/4 8 to 12 NPT, R3/8 15 to 20 NPT, R1/2 20 to 25 8 - Precautions for use with non-SMC Caution (1) When using the KFG2 series with tubing other than those from SMC, the products are not subject to warranty. 3.
Air Source Install an air filter of 5m to the upstream of the solenoid valve (air source side). Install the filter as close to the valve as possible. Air resistance is large and the flow decreases when the filter element is clogged. Clean the filter element.
Table 4 20 25 32 40 Rod seal CM20Z-PS CM25Z-PS CM32Z-PS CM40Z-PS The rod seal is not delivered in sealed packaging for storage independently, so it must be used within 1 year.
P.20 8-1. 8-2. 9. P.21 10. P.22 -1- RS2H (ISO/IEC) (JIS) *1) *2) *1) ISO 4414: Pneumatic fluid power -General rules relating to systems. ISO 4413: Hydraulic fluid power -General rules relating to systems. IEC 60204-1: Safety of machinery -Electrical equipment of machines. (Part 1: General requirements) ISO 10218-1992:Manipulating industrial robots-Safety.
Select an air filter with a filtration size of 5m or smaller. Therefore, take appropriate measures to ensure air quality, by providing an after cooler, or water separator, if needed. Compressed air that contains excessive foreign material may cause malfunction of valves and other pneumatic equipment.
Select an air filter with a filtration degree of 5m or finer. 3. Install an aftercooler, air dryer or drain catch before the filter and take appropriate measures. Compressed air that contains excessive foreign material may cause malfunction of valves and other pneumatic equipment.
A filtration degree of 5m or less should be selected. 3. Install an aftercooler, air dryer or drain catch before the filter and take appropriate measures. Compressed air that contains excessive foreign material may cause malfunction of valves and other pneumatic equipment.
JMHZ2-16D mm 16 MPa 0.1~0.7 (oC) -10~60 (mm) 0.01 (c.p.m.) 120 32.7 (N) 43.5 mm 10 3 4M40.7 8 3.4 8 2 13 - 4-2.3 V114-5LU (oC) -1050( (ms) ON5 OFF4 Hz 20 / m/s2 150/30 V114-5LU L (L) (V) 24 -1010% (W) 0.4 [0.40.1] P .1367 LED 300 14 - 4-3.
Connection thread size Tightening torque [Nm] R1/8 3 to 5 R1/4 8 to 12 R3/8 15 to 20 R1/2 20 to 25 4) Reuse 1. Normally, fittings with a sealant can be reused 2 to 3 times. 2. To prevent air leakage through the sealant, remove any loose sealant stuck to the fitting by blowing air over the threaded portion. 3.
Table 1: Stroke adjustment range (Without spacer, with short spacer, with long spacer) -10 -20 -30 -40 -50 0 0 to 10 10 to 20 20 to 30 L unit MY2*16 Without spacer Short spacer Long spacer H unit 0 to 12 12 to 24 24 to 36 L unit MY2*25 Without spacer Short spacer Long spacer H unit 0 to 16 16 to 32 32 to 48 L unit H unit Without spacer MY2*40 Short spacer Long spacer -9- Warning 1.
Note 20 Basic circuit for using rotary actuator Circuit structure The basic circuit for operating the rotary actuator using an air filter, regulator, solenoid valve and speed controller is shown in Fig. (1) below.
Operation and Adjustment 20-21 9. Trouble Shooting 22 10. How to Replace the Components 23-28 10-1. Bowl Assembly Replacement 23-25 10-2. Element Replacement 26-28 11. Disassembly Drawing 29 12. Dimensions 30 -1- Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage.
(When customers prepare the drain tube, keep its length at 5m or less and the I.D. at 8mm or larger for correct operation of the auto drain) Using the pressure of the compressed air, the drain will be discharged periodically. Fix the outlet end of the tube so as not to swing during discharge. Prevent the drain tube from having a rise in its piping. Do not bend or crush the drain tube.
Connection thread size Tightening torque [Nm] M5 1 to 1.5 G1/8 3 to 5 G1/4 8 to 12 G3/8 15 to 20 G1/2 20 to 25 (2) Insufficient tightening may cause seal failure, or loosen the threads.
G3/8 15 to 20 G1/2 20 to 25 (2) Insufficient tightening may cause seal failure, or loosen the threads. Precautions for use with non-SMC Caution (1) When using the KFG2H*-C series with tubing other than those from SMC, the products are not subject to warranty. Tube Body 8 - 3.
NPT, R1/4 8 to 12 NPT, R3/8 15 to 20 NPT, R1/2 20 to 25 or loosen the threads. (3) Reuse Normally, fittings with a sealant can be reused 2 to 3 times. Caution (4) Once the fitting has been tightened, backing (1) Be certain to wear safety glasses at all times it out to its original position often causes the sealant to become defective.
3.4, 0.2mm'. 3 cores (red. dhile, b a.k). cores (red, back),0 5m oig X .Shock reslslance 1000m/S? l102Gl .lnsulalion resistanceMin. 50O (between lead wi and 6) as memured with a sooVDC meger .
25 30 40 50 60 75 100 125 150 175 200 225 250 275 300 Standard Stroke (mm) Bore Size (mm) 6 8 10 12 16 20 25 MXH MXS MXQ MXF MXW MXP Dual Rods For Twice The Force The MXS, MXQ, and MXW use a twin bore design to double the actuation force while maintaining the single bore height.