EX500 Power Block Specifications Model EX9-PE1 EX Output block (for high-wattage load) Connection block Connection block stations Output block: Max. 8 stations Power supply for output and internal control 22.8 to 26.4 VDC Power supply voltage 20 mA or less Internal power consumption Max. 3.1 A (When using with 3.0 to 3.1 A, the ambient temperature should not exceed 40C, and do not bundle the cable
DOZ is not available. 2 9 Other Option Electrical entry 3 position closed center G: Grommet Lead wire length: 300 mm L: L plug connector With lead wire LN: L plug connector Without lead wire LO: L plug connector Without connector D: DIN terminal 3 3 position exhaust center 4 M: M plug connector With lead wire MN: M plug connector Without lead wire MO: M plug connector Without connector DO
mounted on the same manifold. 3 m 2 stations 02 U side D side 123Stations VVQ100-10A-1 18 stations 18 Electrical entry Multi-connector C Lead wire entry direction Top entry Side entry U S Cable length Without cable With cable (1.5 m) With cable (3 m) With cable (5 m) 0 1 2 3 Option None DIN rail mounted (With standard length of DIN rail) DIN rail mounting style (Without DIN rail) Nil D DO
Therefore, do not operate it in an environment that is exposed to chemicals such as thinner, carbon tetrachloride, chloroform, acetic ester, aniline, cyclohexane, trichloroethylene, sulfuric acid, lactic acid, or water-soluble cutting oil (alkalinic). 2. Operate it away from direct sunlight.
mounted on the same manifold. 3 m 2 stations 02 U side D side 123Stations VVQ100-10A-1 18 stations 18 Electrical entry Multi-connector C Lead wire entry direction Top entry Side entry U S Cable length Without cable With cable (1.5 m) With cable (3 m) With cable (5 m) 0 1 2 3 Option None DIN rail mounted (With standard length of DIN rail) DIN rail mounting style (Without DIN rail) Nil D DO
Note 4) Thermo-cooler specifications do not have heating capability. Note 5) Capacity of the Thermo-chiller outlet when the circulating fluid temperature is at 20C. Note 6) Required flow for cooling capacity or maintaining the temperature stability. When used below the rated flow, use the individually sold, By-pass piping set (Refer to page 95).
60 Hz 200 VAC 50/60 Hz 110 VAC 50/60 Hz 220 VAC 50/60 Hz 24 VDC T -With conduit terminal TS -With conduit terminal and surge voltage suppressor TL -With conduit terminal and light TZ -With conduit terminal, surge voltage suppressor and light D -DIN terminal DS -DIN terminal with surge voltage suppressor DL -DIN terminal with light DZ -DIN terminal with surge voltage suppressor and light DO
1 Size 1 1 2 2 3 1 1/8 G Grommet 2 Size 2 2 3 3 4.5 2 1/4 *1 GS Grommet (With surge voltage suppressor) 3 Size 3 3 4.5 4 6 3 3/8 D DIN terminal (With surge voltage suppressor) Fitting type Face seal fitting/Compression fitting V Face seal tting S Compression tting DL DIN terminal with light (With surge voltage suppressor) Female thread type P Rc female thread N NPT female thread DO
F: 2.08 0.13 Bore size (mm) Cylinder basic weight Standard Stroke CLK2G series CLK2P series Additional weight per 25 mm stroke Bore size (mm) 40, 50, 63 Standard stroke (mm) 50, 75, 100, 125, 150 Single knuckle joint Double knuckle joint (Pin, cotter pin, flat washer are included.) 0.36 0.34 0.22 0.12 0.24 2.04 Limit switch mounting base Dog fitting Foot Pedestal Note) The above values do
When there are stations which do not require wiring (e.g. individual SUP spacer), specify the wiring specification in the manifold specification so that the number of solenoids is the maximum number of solenoids or less.
Intrinsically Safe Valve 5 Port Solenoid Valve Series 53-SY5000/7000/9000 Body Ported Electrical Entry L and LL Hazardous Location Class I Division 1 Groups A, B, C, D Electrical Entry TT Hazardous Location Class I, II, III Division 1 Groups A, B, C, D, E, F, G Single Unit Warning Do not install in Zone 0 (as defined in IEC 60079-10-1: 2008) or Zone 20 (as defined in IEC 60079-10-2: 2009)
Do not use the body A in a continuously rotating place. AQ Body B AS100P AS200P AS250P AS300P Model Rod and applicable tubing O.D. (Metric size) ASV 4 6 6 10 8 4 Flow rate [L/min (ANR)] It may damage the body A or fittings.
Do not use the air cylinder as an airhydro cylinder. This will result in oil leakage and damage the product. 2. Use a thin wrench when tightening the piston rod. 3. Check the mounting direction of the rod end nut (for male thread). Refer to Mounting Procedure on page 367 for details. 4. There are some changes in the dimensions and the specifications of this model from the current model.
Do not indicate lead wire length symbol N (none) for types D-A3, D-A44, D-G-39 or D-K39. Lead wire length symbols: 0.5 m Nil (Example) M9NW 1 m M (Example) M9NWM 3 m L (Example) M9NWL 5 m Z (Example) M9NWZ None N (Example) H7CN Since there are applicable auto switches other than listed, refer to page 326 for details.
You do not need to specify "N" (i.e., without lead wire) for D-A3, D-A44, D-G39, and D-K39. This is the only standard specification automatically available for these models. D-A9V, M9V, M9WV, and M9A(V) models cannot be mounted on 25 to 40. Since there are applicable auto switches other than listed, refer to page 310 for details.
. * Do not indicate sufx N for no lead wire on the D-A3lA/A44A/G39A/K39A models. * Lead wire length symbols: 0.5 m Nil (Example) M9NW 1 m M (Example) M9NWM 3 m L (Example) M9NWL 5 m Z (Example) M9NWZ None N (Example) H7CN *Since there are other applicable auto switches than listed above, refer to page 266 for details.
Do not indicate suffix N for no lead wire on the D-A3lA/A44A/G39A/K39A types. The D-G39A/K39A cannot be mounted on the bore size 20. The D-A9lV/M9lV/M9lWV types and the D-M9lA(V)L type cannot be mounted. Since there are other applicable auto switches than listed above, refer to Best Pneumatics.
Additionally, do not mount the foot bracket with the pressure applied to the port. y 0 A port B port a 1 w y y a e k w of y e e k g n of ra n e io at g ot R n R +4 0 ra ot n io 0 at at ot 8 R io 1 R +4 0 n y ot ra a w n y 0 g at e e k of 9 io 1 n ay ra w n g ey e of k 189
Valve Specifications Caution Do not separate the cylinder from the valve.
(Scratches, scrapes, blotches and uneven color may be present as long as they do not interfere with function or performance.) The symbol refers to surface finishing of JIS G 4305 cold rolled stainless steel sheet. 47 B