Multistage Ejector Series ZL112.212 36 Section A/ With Digital Pressure Switch for Vacuum ZL112-D (ZSE30A) 28 30 (5.8) 4 x M4 Thread depth 8 (Mounting hole) 59 85 1073 Series ZL112 Dimensions: Series ZL112 (With Valve) With supply valve and release valve ZL112-K1L-D P 2 x 5.4 Mounting hole Digital pressure switch for vacuum Exhaust port 13.5 Manual override V P 10 Release valve V S Supply valve Circuit diagram 50 166 4.5 19
Red ON The power supply voltage for control and input is below 19 VDC. (When diagnostic parameter is enabled) PWR(V)-LED LED display Content OFF The power supply voltage for output is below 19 VDC. (When diagnostic parameter is disabled) Green ON The power supply for output is correct. Red ON The power supply voltage for output is below 19 VDC.
indication Functional element (Green) Element requiring replacement (Red) 2 Modular Connection Type Compressed Air Preparation Filter AFF/AM/AMD/AMK Series Lightweight Series Size Weight [kg] Reduction rate [%] Weight AFF/AM/AMD1 20 0.19 b 0.38 50 Max. 50% lighter 1 30 0.39 b 0.55 29 0.19 kg b 0.38 kg 40 0.79 b 0.9 12 50 1.23 b 1.4 12 60 1.46 b 2.1 30 AMK2 20 0.19 b 0.3 37 30 0.39 b 0.48 19
External Dimension Drawing 5-1 Monosashi-kun with Brake 18 19 5-2 Controller 20 5-3 Extension Cable 21 6.
Longer bolts can hit the guide block, which causes operation failure. 19 - 13. In pushing operation, set the product to a position of at least 0.5mm away from a work piece. If the product is set to the same position as a work piece, the following alarm and unstable operation can occur. a.
8 20 0 0.033 13 10.5 8 41 5 28 5 6 30 M8 x 1.25 24 M20 x 1.5 1/8 9 62 14 133 142 25 22 19.5 17 9 30 25 10 19 10 26 0 0.033 13 10.5 8 45 6 33.5 5.5 8 30 M10 x 1.25 30 M26 x 1.5 1/8 9 62 14 137 146 32 22 19.5 17 9 30 25 10 19 12 26 0 0.033 13 10.5 8 45 6 37.5 5.5 10 30 M10 x 1.25 34.5 M26 x 1.5 1/8 9 64 14 139 148 40 24 21 22 10 38 41.2 15 30 14 32 0 0.039 16 13.5 11 50 8 46.5 7 12 39 M14
Appendix B: F-Parameters . 102 19. Appendix C: i-Parameters . 103 20. Appendix D: Diagnostic messages for parameter errors for PROFIsafe .. 104 21. Appendix E: Checklists . 105 22. Appendix F: Safety Characteristics. 109 23. Appendix G: EX245-FPS Timing Values . 110 24. Appendix H: Cybersecurity . 111 3 No.EX##-OMY0004 1.
Initial Setting 19 4.1 Switch setting (EtherCAT ID) 19 4.2 Hardware Configuration 19 5. External Connections 20 5.1 PWR: Power supply connector 20 5.2 MOT: Motor connector, ENC: Encoder connector 20 5.3 SI: Serial I/O Connector 20 (1) Connecting the teaching box 20 (2) Connection with a PC 21 5.4 IN, OUT: EtherCAT communication connector 21 6.
(Refer to "Tube attachment" on page 19.) Mounting with bracket Fix the bracket to the product with the set screws M3 x 5 L (2 pcs.) or M4 x 5 L (2 pcs.) supplied. The required tightening torque is 0.5 to 0.7 Nm for the M3 set screws and 1.4 to 1.6 Nm for the M4 set screws.
Piping to the Vacuum Port Adapter Vacuum port adapter When mounting or removing the fitting, etc. to or from the vacuum port adapter, hold the vacuum port adapter with a wrench (across the flats 19). Recommended tightening torque:3 to 5 Nm The product may break, if it is held by hand.
DICOM 1 Failure Note 3) 9 ALM RA1 N OPC 2 12 MBR RA2 Electromagnetic brake interlock 13 DOCOM S/S Y000 PP 23 COM1 Y010 NP 25 10 m or less COM3 15 LA A phase pulse detector (Differential line driver) Y004 CR 5 16 LAR COM2 17 LB B phase pulse detector (Differential line driver) 18 LBR X INP 10 19 LZ Z phase pulse detector (Differential line driver) 20 LZR X Control common RD 11 14 LG X OP 21
thread size 20 For 20 M8 x 1.25 32 For 25 M10 x 1.25 For 32 M10 x 1.25 40 For 40 M14 x 1.5 Dimensions M, P D M E F C G A B H Standard Pneumatic: Up to 0.7 MPa [mm] Model Connection thread M A B C D E mF G Width across flats H Maximum thread depth P Weight JT20 M8 x 1.25 19.2 8 11 (25.4) 23 10 13.6 22 9.5 22 g JT32 M10 x 1.25 23 10 13.4 (30.6) 28 12 16.3 27 11.5 38 g JT40 M14 x 1.5 29 14 19
HED007-HW13 HED007-HW19 HED007-HW13 HED007-HW19 Temperature controller model HED003-C2A Part number of set HED003-W2A13 HED003-W2A19 HED003-W2B13 HED003-W2B19 HED005-W2A13 HED005-W2A19 HED005-W2B13 HED005-W2B19 HED007-W2A13 HED007-W2A19 HED007-W2B13 HED007-W2B19 HED003-C2B HED005-C2A HED005-C2B HED007-C2A HED007-C2B Heat exchanger HED H W 007 13 Cooling capacity Tube size 003 005 007 13 19
(Operating pressure: 0.5 MPa, unloaded, Piping: Bore 19 mm x 1 m) Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com RHC MK(2) Although the converter and the valve unit are integrated, they can also be operated by connecting individual piping.
No.JSY1000V-OMW0004-A Solenoid Valve PRODUCT NAME JSY1000/3000/5000 Series (Non Plug-in) MODEL/ Series Contents Contents -1 Safety Instructions -2,3 Design / Selection -4 to 6 Mounting -6 Piping -6,7 Wiring -7 Lubrication -7 Air Supply -7,8 Operating Environment -8 Maintenance -9 Specific Product Precautions -10 to 17 Valve Construction -18 Valve Replacement Parts / Pilot Valve -19 Manifold
In addition, the program can be set up to 041A = 1050kPa. 19 - Parameter index 0x4D Parameter name Set value of Solenoid Valve Stop Time Function This function reduces operation of the solenoid valves when the supply pressure is insufficient. Bit Bit 701BYTE Value It can be set from 0% to 99% (of 100 seconds).
(Refer to page 19) 4. Forced input and output The input and output signal of the unit is forcibly operated with the Handheld Terminal. (Refer to page 20) -15No.EX-OML0011-C 1.
Maintenance and Inspection 3.1 Inspection -P. 19 3.2 Maintenance -P. 20 3.3 Replacement Parts -P. 20 4. Troubleshooting -P. 20 -1- Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage. These instructions indicate the level of potential hazard with the labels of Caution, Warning or Danger.
8 above 6 to 15: not available Nickel plated Note 1) Seal kits are sets consisting of numbers 15 through 19. Order using the kit number corresponding to each bore size. Note 2) Adhesives are applied to the secured portion of the head cover and the cylinder tube.