SMC has redesigned the CQ2 compact cylinder with a new body, making it possible to mount auto switches on any of the 4 surfaces, depending on the installation conditions.
SMC has redesigned the NCQ2 compact cylinder with a new body, making it possible to mount auto switches on any of the 4 surfaces, depending on the installation conditions.
CQ2-Z SPL CYL. 558.92000 lb. 493.
Coolant Valve Series SGC Made to Made to order specifications Order How to Order (For details, refer to page 389) Coolant Valve Series SGC Made to Order Made to order specifications (For details, refer to page 389) How to Order External pilot solenoid 2 2 Y 1 A 1 T Z 10 A 05 SGC Air operated 2 2 1 A A 05 10 SGCA q w e r t y u i o !0 !1 !2 !3 !4 !
Z Y69BZ Solid state switches marked with a "p" are produced upon receipt of order. Specifications Lock Specifications Lock position Rear, Front Double acting Action 32 40 50 63 Air Fluid Holding force (max.)
For the old CDM□ series, replace each auto switch with one applicable to the CDM2 □-Z series.
The CM2 series and CDM2-Z series catalogs can be found <a href="/webcatalog/en-jp/seriesList/?type=GUIDE&id=CM2-CDM2-Z-E&show_page=true" target="_blank">herea>.
Refer to page 14 for ordering a coil only. DIN type is available with class B only. Refer to the Table (3) for the available combinations between each electrical option (S, L, Z) and rated voltage. Option S, Z are not available because a surge voltage suppressor is integrated into the AC/Class B, built-in full-wave rectifier type as a standard.
a a a o a o a a a a o a a a a o a a a a a a o a a a i a a a a a a a a a a a a a a a a a a a a a a a a a a a r a a a a a a o a o a SMC Offers the Highest DimensionalAccuracy .
KQ2TW P.153 Use to four-branch a line. P.150 Male run tee KQ2Y Use to branch a female thread in the same direction and at a 90 angle.
A valve, which might potentially cause a hum or buzz can be very annoying to a patient, so a full wave rectified unit for AC service is often preferred. A DC unit, not requiring a rectifier, is sometimes used in specific applications. Also common is a bumper in a 2-way valve, usually just a flat disk with no sealing action.
A valve, which might potentially cause a hum or buzz can be very annoying to a patient, so a full wave rectified unit for AC service is often preferred. A DC unit, not requiring a rectifier, is sometimes used in specific applications. Also common is a bumper in a 2-way valve, usually just a flat disk with no sealing action.
Rc1/4 Rc3/8 Bottom Note) When equipped with control unit, 1 or 2 stations are used for mounting. 6 Series VQ7-6 DIN Connector Type VV71-100 80 2n-Rc1/4, 3/8 100 80 9 37 9 23 14 U side 15 R4.5 Manual override Indicator light R4.5 53.5 P=43 9 9 53.5 P=43 20 9 23 38 B B B B B B B B B SMC SMC SMC A PA PA PA PA A A A A B A L1 L2 L2 L1 B A B SMC A B A 4n-Rc1/4, 3/8 (ports A, B) PA L side R side
As a rule, the electro-pneumatic hybrid regulator should be installed in a location that is free of noise or is shielded. If it must be installed in an environment with poor noise conditions, eliminate the power supply noise by using a line filter, Z-wrap, or a spark killer on the 100V power supply or signal source line.
Hs A B A B 32 to 100 D-A73C D-A80C D-J79C D-A79W D-F7WV D-F7V Approx.
L D-A73 (Example) RS H A Lead wire length RZQ 5 m None Nil L 0.5 m 3 m Z N MI W S Applicable for the connector type (D-C) only.
Normal output Reversed output P_1 = A (A B)/4 n_1 = B + (A B)/4 A = Maximum pressure H_1 = (A B)/2 H_1 = (A B)/2 B = Minimum pressure In the OUT2 setting, the above P_1, n_1 and H_1 will be P_2, n_2 and H_2 respectively.
For a facility having a small installation area (that can not vent the air naturally): Make a forced air exhaust vent on a wall at a high level and an air inlet on a wall at a low level. 3.
Be certain to adopt a reliable connecting method if the rotary table is used very frequently or if it is used in a location that is exposed to a large amount of vibrations. 5. There may be cases in which a speed reduction circuit or a shock absorber is required.
Single vane type Double vane type , 0 5 Chamfer +4 0 a a r r n n 9 0 n n e g g 0 o o g e e i i n t t 1 2 a a 0 a 8 7 t t r o o 1 +4 0 0 0 n R R o e +4 0 +4 0 i t g 0 a n 9 t o a e r R g n n o a ti r a n t o o R ti a t o R Chamfer Chamfer Chamfer Chamfer A port B port A port B port A port B port A port B port For size 40 actuators, a parallel keyway will be used instead of chamfer.
Regarding a vacuum switch valve and a vacuum release valve If a non-vacuum valve is installed in the middle of piping system having a vacuum, the vacuum condition will not be maintained. Use a valve designed for use under vacuum condition. 10.