Mist Separator

Refer to the section [12. Dimensions] (P28) for necessary space. (5) Install vertically so that outlet of drain is downward.

Digital Flow Switch

If the minimum setting unit is 1 L/min, the flow can be displayed in 1 L/min units, i.e. 10, 11, 12. Minimum setting unit N Normal condition (NOR) Reference condition for volumetric flow: 101.3 kPa, 0 C The flow measurement which is converted at normal atmospheric pressure conditions at 0 C.

SYJ Series

Solenoid valve side pin wiring diagram Since voltage specifications other than standard 24 and 12 VDC do not have diodes for polarity protection, be careful not to make errors in the polarity. When wiring is done at the factory, positive (+) is red and negative () is black.

FREE MOUNT CYLINDER

(mm) Operating direction 0. 3 0. 5 0. 7 1. 6 OUT 3 6 IN 21. 2 2. 86 7. 10 11. 3 3. 0 OUT 4 10 IN 66. 0 12. 9 26. 1 39. 3 5.9 OUT 6 16 IN 172 37.2 71. 8 106 5. 9 OUT 20 8 IN 264 58 111 164 11 OUT 25 10 IN 412 95 178 260 16 OUT 32 12 IN 691 173 312 420 Note) Prevent load from being applied to the piston rod when the piston rod is being extended. 6/10 2.

Air cylinder

Standard product: Double acting/single rod Table 12 Parts list No.

Regulator

Regulator (Front pressure gauge connection port) Plug Round type pressure gauge Digital pressure switch Part name Tools Tool size [mm] Recommended torque [N-m] Plug Hexagon wrench key 4 0.55 to 0.65 Round type pressure gauge Wrench 12 7 to 9 Digital pressure switch Wrench 12 7 to 9 -10- Panel mounting 1.

Digital Gap Checker

DIN rail ISA-5Part number L Number of stations ISA-5-1 73.0 1 ISA-5-2 135.5 2 ISA-5-3 173.0 3 ISA-5-4 210.5 4 ISA-5-5 248.0 5 ISA-5-6 285.5 6 Seal for extra station ISA-15 Threaded plug with seal ISA-12Piping type Part number Rc1/8 ISA-12-A : This is applicable in both G1/8 ISA-12-C piping specification C and F. -11No.PS-OMR0002-K 2 About this product Centralized lead wire ISA-19Bracket

IZx-OMR0035

A Emitter cartridge retaining screw Emitter Cartridge (M3 x 0.5 L=12) Emitters (8 emitters are mounted circularly) Caution Do not touch the emitters during cleaning. Using the cleaning kit, saturate the felt with industrial alcohol, insert it into the emitters and rotate several times to clean.

Magnetically Coupled Rodless Cylinder (Slider Type: Slide Bearing)

Fig. 12-1 Correct position Fig. 12-2 Incorrect position 25/28 8. Made to order product A wide range of made-to-order products are prepared depending on operating environment and conditions. Refer to Table 13 for made-to-order products.

Precision Regulator

Troubleshooting 12 8. Dimensions 13 -1- Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage.

In-line Air Filter

ZFC-EL-3 ZFC5 12 x 8 x L20 ZFC-EL-4 ZFC7 16 x 12 x L25 Procedure (1) Stop the operation and release the pressure in the filter to the atmospheric pressure (return the vacuum pressure to the atmospheric pressure). (2) Slide the lock mechanism in the direction of the arrow to release the lock.

VNA Series

Pilot port piping 12(P1) and 10(P2) piping should be as follows according to the model () If the pilot air is not supplied, the valve position will not be held. Pressurize Port 12 (P1 ) or Port 10 (P2) when using the product. Installing a silencer to the exhaust port and the bleed port is recommended for noise reduction and for dust entry prevention.

XLG Series

Period and scope of warranty 12 6. Parts replacement procedure 13 1 XL*-OMI0010-E Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage. These instructions indicate the level of potential hazard with the labels of Caution, Warning or Danger.

Parallel Type Air Gripper

The bead of the dust cover Cross section for dust cover 12 - 3-3. Construction / Parts list, seal list MHZ2-6 Double acting/ Finger open Single acting / Normal open Double acting / Finger close Single acting / Normal closed Double acting/ Finger closed Components Components No. Description Material Remarks No.

11-cq2-e

6 Single acting, spring return Piston seal CQ2B12-S-PS Rod seal NBR 12 16 20 25 32 40 50 CQ2B12-S-PS CQ2B16-S-PS CQ2B20-S-PS CQ2B25-S-PS CQ2B32-S-PS CQ2B40-S-PS CQ2B50-S-PS CQ2B16-S-PS Gasket CQ2B20-S-PS CQ2B25-S-PS CQ2B32-S-PS CQ2B40-S-PS CQ2B50-S-PS Left no. !4. Seal kit includes !4. Order the seal kit, based on each bore size.

11-cqp2-e

4 Pneumatic type (non-lube) Piston seal Rod seal NBR CQ2B12-PS 12 16 20 25 32 40 50 63 80 100 CQ2B12-PS CQ2B16-PS CQ2B20-PS CQ2B25-PS CQ2B32-PS CQ2B40-PS CQ2B50-PS CQ2B63-PS CQ2B80-PS CQ2B100-PS CQ2B16-PS Gasket CQ2B20-PS CQ2B25-PS CQ2B32-PS Set of left nos. !2, !3, !4.

air-filter-e

Fiber Paper Micromesh Specifications Model 4 65 to 70 x L250 FGETB FGETC FGETA FGESA Note 1) FGESB Note 1) FGESC Note 1) FGELA Note 1) FGELB Note 1) FGELC Note 1) Number of elements 8 65 x L250 12 65 x L250 4 Note 2) 8 4 Note 2) 12 4 65 to 70 x L250 4 Note 2) 8 4 Note 2) 12 4 65 x L250 4 Note 2) 4 Note 2) 65 to 70 x L500 65 to 70 x L250 65 to 70 x L750 65 to 70 x L250 65 to 70 x L500 65 to

Rotary Actuated Air Gripper/3-Finger Type MHR3/MDHR3 Series Size: 10, 15

Example) M9NZ Note) When using the 2-color indicator type, please make the setting so that the indicator is lit in red to ensure the detection at the proper position of the air gripper. 530 MHR3/MDHR3 Series Rotary Actuated Air Gripper 3-Finger Type Model/Specifications Nominal size 15 10 Action Double acting External grip 13 7 Holding force (N) (Effective value) (1) at 0.5 MPa Internal grip 12

CUJ

Bore size 1 Hard anodized Aluminum alloy 4 CUJB4-PS Cylinder tube 2 Above numbers 11, 12, 13 and an exclusive grease pack.

MHS

Note 2) When holding a workpiece close at the end of open/close stroke of fingers, detecting performance of the combinations listed in the above table may be limited, depending on the hysteresis of an auto switch, etc. 12-12-12 12-12-13