LEC-T1_C LEC-OM08003 // LEC-T1 Series LEC6 LECPA TB Ver2.1 .5 .7 1. .9 1.1 .9 1.9 2.10 1.2 .11 1.11 2. .12 3. .13 3.1 .13 (1).13 (2)Tree .13 3. .14 (1).14 (2)Tree .15 4.16 5. .17 5.1 .18 5.2 .19 (1).19 (2).19 5.3 .20 (1).21 (1-1) LECPLECA 22 (2) .23 (2-1) LECPLECA 23 (2-1-a) TB Ver1.**. 23 (2-1-b) TB Ver2.**. 25 (2-2) LECPLECA 27 (2-2-a) TB Ver1.**. 27 (2-2-b) TB Ver2.**. 29 (2-3) LECPLECA .32 1
Trouble Shooting 15 8. How to Replace the Components 16-19 8-1. Diaphragm Assembly Replacement 16 8-2. Valve Guide Assembly and Valve Assembly Replacement 17 8-3. Square Embedded Type Pressure Gauge Replacement 18 8-4. Blanking Plate Assembly Replacement 19 9. Disassembly Drawing 20-21 10.
Remove piston seal 3) Tube gasket Pull out with the precision screwdriver. 15 3-2-3. Grease C a u t i o n Use SMCs recommended grease. Grease pack part number: GR-S-010 (10g), GR-S-020 (20g) 1) Rod seal Apply a thin layer of grease to all surfaces of the new seal to make it easy to mount the rod seal and improve sealing.
Tightening Torque for Piping Caution Caution Connection Proper tightening Proper tightening torque (N m ) thread Rc 1/4 8 to12 Rc 3/8 15 to 20 Rc 1/2 20 to 25 Rc 3/4 28 to 30 Mounting Follow the procedure of the manufacture when fittings other than SMC is used. 5.
Terminal no.2 (-) Note 1) The tightening torque should be 0.5 Nm +/15%. Note 2) The applicable outside diameter of cable (7) is 6 to 8 mm. Note 3) Round or Y-shaped crimped terminal cannot be used.
The structure of the entries from Sub-Index 1 to 8 is as follows:Index (16 bit) Sub-Index (8 bit ) Length (8 bit) (MSB)31 16 15 8 7 0 (LSB) Structure of PDO Mapping Entry -24No.EX-OMK0006-C Index 1800h Transmit PDO Communication Parameter Index1800h_Sub-Index1 means COB-ID of PDO.
For details of each setting, refer to page 15 of this manual. Please refer to the PLC manufacturer's manual etc. for details of programming and addresses. For the PLC protocol and programming refer to the relevant manufacturer's documentation.
Remove the excessive input blocks. -57No.EX##-OMO0019 Fault No. 15 Problem Possible cause Investigation method Countermeasures Tighten the screws while holding the input unit and the input block so that there is no gap between them. Tighten the screws to the specified tightening torque.
Doc.No.LV50***-OMQ0004-F Product Name Electromagnetic Digital Flow Switch Model/ Series/ Product Number LFE# SMC Corporation No.LV50***-OMQ0004-F Contents Safety Instructions 2 Model Indication and How to Order 11 Summary of Product Parts 13 Definitions and Terminology 14 Mounting and Installation 15 Installation 16 Piping Method 17 Wiring 19 Maintenance and Inspection 21 Troubleshooting
Number of CH occupied by PLC Number of point occupied by one node address Setting range Max. number of connected slave IN1/OUT1 8 IN : 0 to 1 OUT : 0 to 1 IN 2 OUT 2 IN2/OUT2 8 IN : 0 to 3 OUT : 0 to 3 IN 4 OUT 4 IN4/OUT4 8 IN : 0 to 7 OUT : 0 to 7 IN 8 OUT 8 IN1/OUT1 4 IN : 0 to 3 OUT : 0 to 3 IN 4 OUT 4 IN2/OUT2 4 IN : 0 to 7 OUT : 0 to 7 IN 8 OUT 8 IN4/OUT4 4 IN : 0 to 15 OUT : 0 to 15
Correct mounting position of auto switch Refer to figure-15 and 16 for correct auto switch mounting position.
If the switch output is unnecessary, it is available just like a pressure gauge. page 14 ON Indication color Selects the color to indicate. page 14 ON: Green OFF: Red Response time Sets of a response time prevents chattering in output. page 15 1 s Operation mode Selects the mode to operate the Pressure switch. page 15 Hysteresis mode Hysteresis page 17 0.01 MPa (1 psi) Output type Sets the
ZL-OM00801 Contents Safety Instructions 2 Model Indication and How to Order 10 Mounting and Installation 12 Air Supply 12 Supply Pressure 13 Piping 13 Solenoid Valve 15 Construction 15 Maintenance and Inspection 17 Exhaust from Ejector 19 Specifications 19 Circuit Diagram 22 Weight 23 Exhaust Characteristics and Flow Characteristics of Ejector 24 Flow Characteristics Curves 25 Vacuum Pressure
20 25 30 15.0 11.5 23.0 10 5 10 15 20 25 30 35 40 45 18.0 10.5 21.0 16 5 10 15 20 25 30 35 40 45 20.0 13.0 26.0 * The above numbers are references for the mounting positions of those auto switches that detect a stroke end.
Note 1) Tighten within the tightening torque of 0.5 Nm +/-15%. Note 2) Cable (7) external: 6 to 8 mm (1) (2) (6) (5) (4) (3) (7) (8) (11) (9) (10) Figure-1 9 VG300-OMH0002-B TROUBLE SHOOTING Should any trouble be found during operation, trace the source of the trouble in the following or der and take correcitve action.
If the heater 0 5 10 15 20 25 30 temperature is over 200oC or valve temperature is Time (sec.) Time (sec.) ( Duration of the inrush current flow (as a guide) Duration of the inrush current flow (as a guide) over 150oC, please use thermostat to control the heaters to prevent overheating.
Basic Circuit for Cylinder Operation 15 5. Troubleshooting 16~17 6. Construction and Material 18~23 -1- Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage. These instructions indicate the level of potential hazard with the labels of Caution, Warning or Danger.
DIMENSIONS 15 REGULATOR Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage. These instructions indicate the level of potential hazard with the labels of Caution, Warning or Danger.
Maintenance and Inspection 3.1 Inspection -P. 15 3.2 Maintenance -P. 15 3.3 Replacement Parts -P. 15 4. Troubleshooting -P. 16 -1- Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage. These instructions indicate the level of potential hazard with the labels of Caution, Warning or Danger.
*In the case of N.O. specification, 1(P) port. (15) Supply specified pressure to X port. (Single solenoid, 3 position: 0.2 to 0.9 MPa, Double solenoid: 0.1 to 0.9 MPa) If no improvement is achieced in spite of the above countermeasure, inside of the valve may have some abnomality. In this case, stop using the balbe immediately.