3 Port Solenoid Valve Metal Seal Series VZ200 1 If the socket will be used again, first spread the hook outward. Connector assembly with protective cover Connector assembly with protective cover enhances dust protection. Effective to prevent short circuit accidents due to penetration of foreign matter into the connector section.
If the rod diameter is not the appropiate one in relation to the pressure and the stroke, a longer stroke cylinder should be selected or pressure should be reduced.
pin should be used together with a plain washer.
As a guide, the area to be heated on the tubing is the length to the insert pin base. Heat gun Be careful not to burn yourself! Heat it up for 15 to 20 seconds at about 400C. Do not touch heated areas (tubing, heat gun). Also, be careful not to touch the other side of the heated area since the temperature also increases there due to hot air.
OElectrical currenl should be kept within lhe operating current range. When used at cuffent levels less than lhe operating current range, the indicator light will not turn on, and if operated in excess of the operating current range, the indicator light will be damaged. O Prevent lepsaled bending ol vtires.
D1 D2 L TKS-06 Orange TRB0604, TRBU0604 16 58 45 TKS-08 Yellow TRB0806, TRBU0805 18 TKS-DPH00071 (10 replacement blades) 35 TKS-10 Blue TRB1075, TRBU1065 20 62 50 TKS-12 Green TRB1209, TRBU1208 22 Inner tubing material/TRB: Nylon, TRBU: Polyurethane Dimensions D2 D1 L 9.7 (3/8") Able to strip without damaging the inner tubing The outer tube can be stripped without damaging the inner tube
OElectrical currenl should be kept within lhe operating current range. When used at cuffent levels less than lhe operating current range, the indicator light will not turn on, and if operated in excess of the operating current range, the indicator light will be damaged. O Prevent lepsaled bending ol vtires.
Turn it right to release. 3.8 Change of electrical entry Wire entry can be changed by mounting the housing in either direction (four directions at every 90) after dividing the terminal block and the housing. For the indicator lighted style, be careful not to damage the light with the lead wire of the cable. PUSH TURN Precaution Insert/remove the connector vertically, not at an angle.
VACUUM UNIT, PUMP SYSTEM, VACUUM EJECTOR, M18, 111.00000 lb
methylamines, hydrochloric acid or sulfuric acid is splashed over, so it cannot be used.
Caution Be sure to read before handling.
When mounting the SYJ500 valve on the SYJ5000 manifold, the SYJ500 solenoid must be positioned on the same side of the manifold as a single solenoid SYJ500. (Refer to the figure below.) For base mounted style, the A port of the 3 port valve flows out the B port of manifold base. Spacer type regulating valve on manifold block can regulate the pressure to the valve individually.
Put the "" symbol at the beginning of the part numbers for solenoid valves, etc., which are to be mounted. Valve stations are numbered from station 1 on the D side. Indicate the valves to be mounted below the manifold part number, in order starting from station 1 as shown in the drawing.
The scraper can be carefully pried out, and replaced with a press fit using a manual arbor press.
1. 7 stations (15 stations) Note 1) Be careful that the packing and the O-ring do not fall out of the groove. Note 2) The tightening torque of bolt !1 should be 2 to 2.2 N. (2) (1) 8 stations Note 1) Regardless of the D-sub connector mounting position, stations are to be counted from D side as the 1st one. Note 2)D-sub connector can use up to 8 stations in on side fitting (Type FD U).
1. 7 stations (15 stations) (2) (1) Stations Note 1) Be careful that the packing and the O-ring do not fall out of the groove. Note 2) The tightening torque of bolt !1 should be 2 to 2.2 N. Note 1) Regardless of the D-sub connector mounting position, stations are to be counted from D side as the 1st one. Note 2) D-sub connector can use up to 8 stations in on side fitting (Type FD U ).
Note 2) 5 to 50C when the digital pressure switch will be used. OUT 2 Refer to pages 734 and 736 for the digital pressure switch and pressure switch specifications. 717
Removal of stripped tubing is unnecessary Pawl Can be attached to tools Since the stripped tubing is discharged to the outside, no additional labor is required to remove it. Stripping work can be automated by attaching to an air driver, etc. Window Socket adapter Even double layer polyurethane tubing (series TRBU) which is highly adhesive to the external layer can be stripped easily.
Speed Controller with Residual Pressure Release Valve with One-touch Fitting ASFE Series RoHS Residual pressure can be easily released with one push of button. Model Elbow type Applicable tubing O.D.
Example) AS2201FS-G01-06 0 Meter-out 1 Meter-in Note) Meter-out and meter-in types can be visually identied by color of the knob. Meter-out: Gray Meter-in: Light blue Applicable tubing O.D.