JXCx-OMU0024 Drive is ON when SVRE is OFF (01-098) C Input RESET
-8VEX-OMO0001 P1 P1 02A 3R (VBA1-10) 3R () PE 3R PE 2A / (VBA1-10) P1 O PE 3R 02A 3R 2A / 2A -9VEX-OMO0001 Revision history 4-14-1, Sotokanda, Chiyoda-ku, Tokyo 101-0021 JAPAN Tel: + 81 3 5207 8249 Fax: +81 3 5298 5362 URL http://www.smcworld.com Note: Specifications are subject to change without prior notice and any obligation on the part of the manufacturer. 2010 SMC Corporation
16 No.VQZ100V-OMT0001 Revision history TW 4-14-1, Sotokanda, Chiyoda-ku, Tokyo 101-0021 JAPAN Tel: + 81 3 5207 8249 Fax: +81 3 5298 5362 URL http://www.smcworld.com Note: Specifications are subject to change without prior notice and any obligation on the part of the manufacturer. 2008 SMC Corporation All Rights Reserved No.VQZ100V-OMT0001
For example, install a ventilation opening, etc. in order to prevent pressure from increasing inside of the confined area and to release the heat generated by the valve. 10. Extended periods of continuous energization If a valve will be continuously energized for an extended period of time, the temperature of the valve will increase due to the heat generated by the coil assembly.
Maintenance Warning Please refer to the attached Procedure for maintenance. 10 - 7Troubleshooting Status Possible cause Countermeasure Operating pressure is too low Increase pressure to 0.45MPa or more.
Function selection mode ON OFF Front protective cover (Model: ZS-27-01) Connector Connecting / Disconnecting When mounting the connector, insert it straight into the socket, holding the lever and connector body, and push the connector until the lever hooks into the housing, and locks.
Piping specification: -01, -N01 After hand tightening, hold the hexagonal spanner flats of the pressure port with a spanner, and tighten with 2 to 3 rotations. As a reference, the tightening torque is 3 to 5 Nm. When tightening, do not hold the pressure switch body with a spanner. or longer simultaneously.
Piping specification: -01, -N01 After hand tightening, hold the hexagonal spanner flats of the pressure port with a spanner, and tighten with 2 to 3 rotations. As a reference, the tightening torque is 3 to 5 Nm. When tightening, do not hold the pressure switch body with a spanner. or longer simultaneously.
Piping specification: -01, -N01 After hand tightening, hold the hexagonal spanner flats of the pressure port with a spanner, and tighten with 2 to 3 rotations. As a reference, the tightening torque is 3 to 5 Nm. When tightening, do not hold the pressure switch body with a spanner. longer simultaneously, the main display shows [-], and the reset to zero.
Piping specification: -01, -N01 After hand tightening, hold the hexagonal spanner flats of the pressure port with a spanner, and tighten with 2 to 3 rotations. As a reference, the tightening torque is 3 to 5 Nm. When tightening, do not hold the Z/ISE20 body with a spanner. Pressure second or longer simultaneously.
Maintenance Bracket A or D(Model: ZS-24-A/ZS-24-D) Bracket B (Model: ZS-24-B) [01/N01 type] [W1/WF1 type] Operator How to reset the product after power cut or forcible de-energizing The setting of the product will be retained as it was before a power cut or de-energizing.
HOW TO ORDER 1315 10. DISASSEMBLY DRAWING 1618 11. DIMENSIONS 19 MICRO MIST SEPARATOR REGULATOR Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage. These instructions indicate the level of potential hazard with the labels of Caution, Warning or Danger.
OUT2 ( ) ( ) ( ) ( ) For compound For vacuum For low pressure For positive pressure 101 kPa -101 kPa [Default setting] 101 kPa 1 MPa During the zero clear operation, pressure above 5%F.S. (2.5%F.S. for compound pressure) has been applied. After 2 s, the mode will reset to the measurement mode. The set values are displayed in auto-preset as follows.
They are all important notes for safety and must be followed in addition to International standards (ISO/IEC) and other safety regulations. ( ) For compound 101 kPa ( ) For low pressure 100 kPa ( ) For positive 1 MPa ( ) For vacuum -101 kPa [Default setting] ( ) For low differential 2 kPa ( ) For positive 500 kPa N.C.
Base Mounted Wiring: 10 (Non Plug-in Individual Lead Wire Entry), Stations: 10 Stations, Passage: 1 [P(SUP): Common, E(EXH): Common, Port A,B(CYL): Side], Port Size: 01 (1/8)
This is a legacy product. Please contact us for the latest version.sales@ocaire.com
Base Mounted Wiring: Non Plug-in Individual Lead Wire Entry, Stations: 10 Stations, Passage: 1 [P(SUP): Common, E(EXH): Common, Port A,B(CYL): Side], Port Size: 1/8, Thread: -, Control Unit: -, Voltage Air Release Valve: -
For vacuum/ compound pressure ISA2 ZSE30A 01 N M Option 3 Note) Calibration certificate Nil Y K T Note) Operation manual ISE35 Symbol Rated pressure range ZSE30A ZSE30AF 0 to 101 kPa 100 to 100 kPa PSE Piping specifications IS 01 Note) All texts in both English and Japanese.
Panel mount adapter ZS-46-B Panel mount adapter + Front protection cover ZS-46-D Lead wire with connector ZS-46-3L 3-core, 2 m, Non-waterproof (Without waterproof cover) Front protection cover ZS-27-01 D Panel mount adapter + Front protection cover ZS-46-D R1/8 Piping adapter ZS-46-N1 NPT1/8 Piping adapter ZS-46-N2 9
Panel mount adapter ZS-46-B Panel mount adapter + Front protection cover ZS-46-D Lead wire with connector ZS-46-3L 3-core, 2 m, Non-waterproof (Without waterproof cover) Front protection cover ZS-27-01 D Panel mount adapter + Front protection cover ZS-46-D R1/8 piping adapter ZS-46-N1 NPT1/8 piping adapter ZS-46-N2 7