IDX-OM-W010 Do not bring the product lying sideways. If you lay it sideways, it will be broken. Do not hang up the product. Do not transport the product with any part such as an air filter mounted on the fittings at the air inlet or outlet port of the product.
Do not drop or bump. Do not drop, bump, or apply excessive impacts (300m/s or more) while handling. Even if the switch body is not damaged, there may be internal damage and possible malfunction. 2. Do not carry an actuator by the auto switch lead wires. Never carry an actuator by its auto switch lead wires.
Do not ground to water pipe, gas tube Do not ground to water pipe, gas tube or lightening rod line. 7. Do not connect too many wires to the same outlet, which could results in heat generation and fire. . Do not connect too many wires to the same outlet, which could results in heat generation and fire. .
When handling and assembling units: Do not touch the sharp metal parts of the connector or plug. Do not apply excessive force to the unit. The connecting portions of the unit are firmly joined with seals. When joining units, take care not to get fingers caught between units. Injury can result. 2. Do not drop, bump, or apply excessive impact.
Do not use the product in an environment subject to a temperature cycle. It will cause failure of the controller or its peripheral devices. 15. Do not use the product in a place where surges are generated.
Do not use the product in the presence of a magnetic field. Malfunction can result. Do not let foreign matter, such as wire debris, get inside the product. Otherwise it can cause damage or malfunction. Do not use the product in an environment that is exposed to temperature cycle.
Do not use the product in the presence of a magnetic field. Malfunction can result. Do not let foreign matter, such as wire debris, get inside the product. Otherwise it can cause damage or malfunction. Do not use the product in an environment that is exposed to temperature cycle.
Do not Do not use in an atmosphere containing flammable or explosive gases. Fire or an explosion may result. This product is not explosion-protected. Do not Do not use the product in a place where static electricity is a problem. Otherwise failure or malfunction of the system can result. Do not Do not cut off the power and compressed air supplied to this product while it is operating.
Do not use a cable longer than 30 m. When using it as an IO-Link device, do not use a cable longer than 20 m. Wire the DC (-) line (blue) as close as possible to the power supply.
Safety Instructions Warning Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use.
Do not use in atmospheres of corrosive gases, chemicals, sea water, water, water steam, or where there is direct contact with any of these. 2. Do not use in direct sunlight. 3. In locations near heat sources, protect against radiated heat. 4. Do not use in locations where static electric charges will be a problem. This may cause system failure.
Do not connect the earth to a water pipe, a gas pipe, or a lightening rod. Do not plug too many leads into a single socket. That causes exothermic heat or fire. Do not modify the internal electrical wiring of the product. 10.2 Specifications An earth leakage breaker is installed in the product.
Do not drop or bump. Do not drop, bump or apply excessive impact (1,000 m/s2) when handling. Even if the switch body is not damaged, the switch may suffer internal damage that will lead to malfunction. 2. Hold the product from the body side when handling. The tensile strength of the power cord is 49 N, and pulling it with a greater force can cause failure. 3.
(Do not tighten with pliers.) I @silrc SERIES NCDJ2 Connection examples to relay and solenoid valve Basic wiring 3 wire system (When power source for switch and load is common) Rd lead wi: Connect io the power sourc e (powet source lerminal) lo operare main circuit of switch.
Cassette base DIN r. ) No,eJ n case of DC cny DLN ra L 1t .gs are alacred DIN rail length DoLrbre wing specilcal,on SDge doube and 3 posrton soleno d va vcs ca. 0e used on a manrfold slatons Nole 2) Speclied layoul Indrate w r ng spec fcal ons on a man Io d specJ.at on sheel Nole thal do!
Note 2) Do not release the OUT side piping port of the product directly to the atmosphere without connecting piping. If the product is used with the piping port released to atmosphere, accuracy may vary.
NT-02 NT-03 NT-04 26 30 25.5 M20 x 1.5 8 13 15.0 12.5 M8 x 1.25 5 32 37 31.5 M26 x 1.5 8 17 19.6 16.5 6 M10 x 1.25 41 47.3 40.5 M32 x 2.0 10 22 25.4 21.0 8 M14 x 1.5 Trunnion Nut Material: Carbon steel (mm) C D d H B Applicable bore size (mm) 20 25, 32 40 Part no.
Do not indicate suffix N for no lead wire on D-A3/A44/G39/K39 models. Lead wire length symbols: 0.5 mNil (Example) M9NW 1 m M (Example) M9NWM 3 m L (Example) M9NWL 5 m Z (Example) M9NWZ None N (Example) H7CN -X Individual -X Since there are other applicable auto switches than listed, refer to page 1214 for details.
(Do not tighten with pliers.) @silrc I SERIES NCDJ2 Connection examples to relay and solenoid valve Basic wiring 3 wire system (When power source for switch and load is common) Rd lead wi: Connect io the power sourc e (powet source lerminal) lo operare main circuit of switch.