Speed Controller with One-touch Fittings In-line Type/Panel Mount Type AS 1F-3 Series size Inch size Model Installment of hexagon nuts on panel nuts up and down in two locations enables user to mount or remove it depending upon the situation. 3.2 1 8" 4 6 8 10 12 5 32 " 3 16 " 1 4" 5 16 " 3 8" 1 2" AS AS1001F AS2001F AS-FE AS2051F Panel KE AS3001F AS4001F AS-FG Panel nut Specifications AS-FP Hexagon nut Air Fluid AS-FM 1.5 MPa Proof pressure 1 MPa Max. operating pressure AS-D
) Refer to burst pressure characteristics chart Air: 4 to 140F (20 to 60C) Water: 32 to 105F (0 to 40C) (With no freezing) Nylon 12 Operating temperature Material Hardness Shore D 70 Burst Pressure Characteristics Chart 2175 Burst Pressure psi 1885 T0425, T0604 1595 Other than T0425, T0604 1305 1015 725 435 Max. operating pressure 0 145 4 32 70 105 140 Operating temperature F TUB-1
I t ll ft l ft th i t d th The fluctuation of the power supply voltage is too large. Install a power supply transformer or use a different power supply to provide appropriate voltage. The fluctuation of the power supply voltage should be kept within +/-10% of the rated voltage. The built-in overload relay of the compressor for refrigeration has started.
cooling Corrugated fin tube type with forced air cooling Refrigerant R407C(HFC) Refrigerant Charge Quantity 42010g 73010g 55010g 67010g Air IN/OUT Connection R1 R1-1/2 R2 Drain Connection (Outside Diameter of Tubing) 10mm Painting Finish Melamine baking finish Colour Munsell 10Y8/0.5 (Urbanwhite) Weight 54kg 62kg 100kg 116kg Note1: The data for m3/h (ANR) is referring to the conditions of 20C
Precision measuring equipment (3-D measuring machines) Semiconductor manufacturing equipment Semiconductor inspection equipment Dental equipment Chemical analysis equipment Ozonizers, Hydrogen gas generating equipment Air (oxygen, nitrogen, etc.)
(coil temperature 20C (68F), at rated voltage, without surge voltage suppressor) Note 2) Impact resistance: No malfunction when tested with a drop tester in the axial direction and at a right angle to the main valve and armature, one time each in both energized and deenergized states.
(choked flow) Subsonic flow : Flow greater than the critical pressure ratio Standard condition : Air in a temperature state of 20C, absolute pressure 0.1 MPa (= 100 kPa = 1 bar), relative humidity 65%. It is stipulated by adding the abbreviation (ANR) after the unit depicting air volume.
(coil temperature 20C, at rated voltage, without surge voltage suppressor) Note 2) Impact resistance: No malfunction when tested with a drop tester in the axial direction and at a right angle to the main valve and armature, one time each in both energized and deenergized states.
Maintenance Caution Model A B C D E Mounting dimension J H L K G F Port size Nominal size (B) ID200 240 240 320 320 1.
. *2 10 to 500 Hz for 2 hours in each direction of X, Y, and Z (De-energized, Initial value) *3 3 times in each direction of X, Y, and Z (De-energized, Initial value) Weight Supply Valve/Release Valve Specifications *1 Based on JIS B 8419: 2010 dynamic performance test (Standard type: Coil temperature 20C, at rated voltage, without surge voltage suppressor) * Refer to the Web Catalog for
(Inlet air pressure: 0.7 MPa, Inlet air temperature: 20C) Accessory (Option)/Replacement Parts Applicable model ID20 ID30 ID40 ID60 6604113 6604113 660651 660651 ID-200S ID-300S ID-400S ID-600S ID-200Z ID-300Z ID-400Z ID-600Z ID-DPM8 Bracket Adsorbent set Note) Adsorbent set (for low dew point) Note) Indicator set Note) Adsorbent and adsorption tube filter for one air dryer (two adsorption
D-DN This catalog is printed on recycled paper with concern for the global environment.
Maintenance Caution Model A B C D E Mounting dimension J H L K G F Port size Nominal size (B) ID200 240 240 320 320 1.
The value of the minimum bending radius is measured at the temperature of 20C as shown below. KP LQ MQR Bend the tube into U-form at a temperature of 20C. Fix one end and close loop gradually. Measure 2R when the tube breaks or is crushed. T T Fixed end IDK 3.
Note 2) The maximum operating pressure is the value at 20C. Refer to the burst pressure characteristics curve for other temperatures. Furthermore, an abnormal temperature rise due to adiabatic compression can cause tubing to burst. Note 3) The minimum bending radius indicates the value at a temperature of 20C with an outside diameter change rate of 10% or less.
(mm) 7.3 5.8 4.4 2.8 8.8 Black (B) White (W) Bend the tube into U-form at a temperature of 20C. Fix one end and close loop gradually. Measure 2R when the tube breaks or is crushed. Blue (BU) Fixed end Translucent (N) Fluid Air 20C 0.8 Max.