0.4 Specify the mounting position, as well as the EXH block base or EXH block plate position by means of the manifold specification sheet. The block plate is used in one or two places for one set. An EXH block base assembly is used in the blocking position when ordering an EXH spacer incorporated with a manifold no.
Do not use One-touch fittings in the piping for an air-hydro cylinder, as oil leakage may occur. 2. For air-hydro cylinder piping, use hard nylon tubing or copper piping. As in the case of hydraulic circuits, surge pressures greater than the operating pressure may occur in an air-hydro cylinders piping, making it necessary to use safer piping materials. Caution 1.
Origin Home Switch Infotmation LX series actuators are available with an optional photo micro sensor as an origin home switch to detect when the actuator is fully retracted. The LCOC seies positioning drjver requires an input from the origin home switch or some other sensor when homing the actuator.
Do not use the product in an environment where the product is constantly exposed to water or oil splashes. If the product is to be used in an environment containing oils or chemicals such as coolant or cleaning solvent, it may be adversely affected (damage, malfunction, or hardening of the lead wires). Do not use in an area where surges are generated.
Stroke A Dimensions (Dimensions other than below are the same as standard type.)
The length of the lead wires between the switch unit and contact protection box should be no more than 1m, and they should be placed as close together as possible. Tighten with a torque of 0.10 to 0.20Nm. As a rule, it should be turned about 90 past the point at which tightening can be felt.
HOLD/CLR setting (Switch No.1) The setting is as follows. The setting at shipment is turned OFF, set to CLR. HOLD/CLR No.1 Function CLR OFF Output is cleared when an error occurs. HOLD ON Output is held when an error occurs.
Please See Below for How to Order Seal Kit 14* Rod Seal NBR Available only as an Assembled Item. Please See Below for How to Order Seal Kit 15* Piston Seal NBR Available only as an Assembled Item. Please See Below for How to Order Seal Kit 16* Cushion Valve Seal NBR Available only as an Assembled Item.
The I/O map is shown with the following unit configuration as an example.
Since no protective cover is installed on the product, provide an external protective cover protecting the entire product wherever possible. Using the product in an environment where it is exposed to water, liquid coolant or dust such as iron powder will cause an adverse effect to the ball screw and the guide. Therefore, an external cover is also required for dust prevention. 8.
If the product is to be used in an environment containing oils or chemicals such as coolant or cleaning solvent, even for a short time, it may be adversely affected (damage, malfunction, or hardening of the lead wires). -6No.PS-OMV0004-H Do not use in an area where surges are generated.
If the product is to be used in an environment containing oils or chemicals such as coolant or cleaning solvent, even for a short time, it may be adversely affected (damage, malfunction, or hardening of the lead wires). Do not use in an area where surges are generated.
When designing an application, be sure to allow sufficient clearance for maintenance and inspections. 4. Keep wiring as short as possible.
An over current (1) Check that there is no noise interference such as static electricity, and check for noise sources. error (Er1, Er2) is displayed.
If using in an environment that is exposed to water splashes, please take measures such as using a cover. If the product is to be used in an environment containing oils or chemicals such as coolant or cleaning solvent, even for a short time, it may be adversely affected (damage, malfunction etc.).
If the product is to be used in an environment containing oils or chemicals such as coolant or cleaning solvent, even for a short time, it may be adversely affected (damage, malfunction, or hardening of the lead wires). Do not use in an area where surges are generated.
Keep wiring as short as possible to prevent interference from electromagnetic noise and surge voltage. Do not use a cable longer than 30 m. Wire the DC (-) line (blue) as close as possible to the power supply.