Table of Contents How to Order . 60 61 62 63 64 66 67 69 69 70 71 72 74 75 76 76 77 78 78 80 81 82 84 88 89 90 91 Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com 92 93 94 94 95 95 95 95 96 96 96 96 96 97 97 98 98 99 99 99 100 100 102 103 103 104 106 106 107 109 111 111 Caution .
L/min) Switch ON point 90 L/min or more Switch OFF point Below 90 L/min (0 is displayed) -50No.PF-OMU0007-D [F30] Accumulated value hold setting This function enables the accumulated flow value to be stored in permanent memory every 2 or 5 minutes.
Compatibility is indicated for temperatures at 90 oC or less. The product does not have an explosion proof construction.
[F 3] Digital filter setting is completed. 1: Each set value is a guideline for 90% response time. 2: Both the switch output and flow display are affected. When only switch output needs to be affected, select the delay time setting.
[F 3] Response time setting is completed. 1: Each set value is a guideline for 90% response time. 2: Both the switch output and flow display are affected. When only switch output needs to be affected, select the delay time setting.
position 90% input value setting (%) (%) or 100% position 100% input value (%) setting (%) Fig. 40-3 No.IP8S-OM09 55 (800) PID constant setting PID constant setting is possible.
HART Communication 30 h Pistonrod Retract end Moving area Output current value Total time (h) Display time (h) Piston movement 0% 5% ~5% ~4.8mA 3.125 3 10% 5~10% 4.8~5.6mA 0.625 0 10~30% 5.6~8.8mA 2.5 2 30% 30~50% 8.8~12mA 6.25 6 50% 50~70% 12~15.2mA 2.5 2 70% 70~90% 15.2~18.4mA 7.5 7 90% 95% 90~95% 18.4~19.2mA 1.875 1 100% 95%~ 19.2mA~ 5.625 5 Extended end (Set point by calibration) Total
W(kg) W(kg) W(kg) W(kg) 6 40 6 15 8 30 8 6 8 10 5 5 20 4 5 12 10 16 10 12 16 10 2 0 0 0 0 100 200 300 400 500 600 V (mm/s) 0 100 200 300 400 500 600 V(mm/s) 0 100 200 300 400 500 600 V(mm/s) -9- (1)(DC24V) LEFS40 (mm) 1) 200, 300, (400), 500, (600) (700), 800, (900), (1000) 50 60 (kg) ) 23 (mm/s) 2) 20500 10250 (mm/s 2) 3,000 (mm) 0.02 (mm) 20 10 (m/s 2) 3) 50/20 () 540 (%) 90
Electric actuators/Common precautions . 90 18.1 Design and selection . 90 18.2 Mounting . 91 18.3 Precautions for Use . 91 18.4 Operating environment . 93 18.5 Maintenance . 93 18.6 Precautions for electric actuator with lock . 94 19.
Lock pin Adapter Right angle square type pressure gauge assembly Product Example: Rotate by 90 degrees from standard orientation Adjustment of orientation of pressure gauge scale plate The pressure gauge is secured to the right angle adapter by means of screws and by removing the screws, it is possible to adjust the mounting orientation of the scale plate in 90 degrees rotations.
The time from when the flow is applied as a step input (when the flow rate changes from 0% to 100% instantaneously) until the switch output turns ON (OFF) at 90% of the rated flow rate.
Refer to the chart on page 35. 3: The response time is when the set value is 90% in relation to the step input.
output signal is turned on from Area 1:80[mm] between Area 2:90[mm].
Push down the lever 90 degrees to pull out the shock absorber. 6-2. Fix the shock absorber with a set screw. Set screw tightening torque: 1.5 Nm Lever Caution After replacing the shock absorber, tighten the set screw firmly and apply grease to the shock absorber rod end surface (Fig.7).
When you begin to feel that the screw is being tightened, turn it further by 90. Caution 2mm or more When using an auto switch on the mounting plate side, the switch will protrude from the end face as shown below. Please provide a run off apace of 2 mm or deeper on the mounting plate. "Runoff" 12-3-25
Mounting Bolt for CDQSW/With Auto Switch Mounting bolt M3 X 35l X 40l X 45l X 50l X 55l X 60l M3 X 35l X 40l X 45l X 50l X 55l X 60l M5 X 45l X 50l X 55l X 60l Mounting bolt M5 X 65l X 70l X 75l X 80l X 85l X 90l M5 X 45l X 50l X 55l X 60l X 65l X 70l X 75l X 80l X 85l X 90l Model C Model C D 65 70 75 80 85 90 45 50 55 60 65 70 75 80 85 90 D 35 40 45 50 55 60 35 40 45 50 55 60 45 50 55 60
When you begin to feel that the screw is being tightened, turn it further by 90. Caution 2mm or more When using an auto switch on the mounting plate side, the switch will protrude from the end face as shown below. Please provide a run off apace of 2 mm or deeper on the mounting plate. "Runoff" 12-3-25
Locking style Turn 90 to counterclockwise pushing M/O button. Lock is released when G on cap and H OFF mark on M/O button correspond. (Lock remains released.) When locking is desired, turn M/O button clockwise 90 while pushing fully, correspond G on cap and H ON mark on M/O button. The correct position is confirmed by click sound "click".
When you begin to feel that the screw is being tightened, turn it further by 90. Caution 2mm or more When using an auto switch on the mounting plate side, the switch will protrude from the end face as shown below. Please provide a run off apace of 2mm or deeper on the mounting plate.
Mounting bolt M5 X 75l M5 X 85l M5 X 80l M5 X 90l M5 X 90l M5 X 100l M5 X 80l M5 X 90l M6 X 105l M6 X 135l M8 X 105l M8 X 135l D 75 85 80 90 90 100 80 90 105 135 105 135 Part No.