Low Friction Cylinders Metal Seal Type low speed actuation (no control of cylinder output) Example 2) Low speed with output control Precision restrictors Solenoid valve ITV (Electro-pneumatic regulator) Mist separator (0.01 m or less) (0.3 m or less) Mist separator (0.3 m or less) Air filter (5 m or less) IR (Precision regulator) W Air filter (5 m or less) IR (Precision regulator) W When performing control of cylinder output, do
Do not subject the gauge to impacts, such as dropping, during transportation and mounting. This can cause loss of indication accuracy. 2. Do not use in locations with high temperature and humidity. This can cause malfunction. 3. When screwing the pressure gauge into place, be sure to apply your wrench on the square wrench flats.
Do not use tools on the pressure regulator knob as this may cause damage. It must be operated manually. Caution 1. Be sure to unlock the knob before adjusting the pressure and lock it after setting the pressure. Failure to follow this procedure can cause damage to the knob and the outlet pressure may fluctuate.
SG 12 Note 1) Do not orient diodes incorrectly. The amp will fail if connected incorrectly. Servo ON Note 2) Wiring for a standard cable less than 10m. When the cable length is 10m or longer, four lines each of P5 and LG wires should be connected in parallel.
Make sure that the lead wires do not interfere with the slide table at any stroke range. Lead wire cover Figure 3.
Do not connect the white wire of the sensor to . View A Terminal block number 4 3 2 1 1 2 3 4 5 6 7 8 8 7 6 5 20 For Water Digital Flow Switch/High Temperature Fluid Type Series PF2W Refer to www.poweraire.com for details of products compatible with overseas standards.
Perform changes of the detection position under the same conditions as step 3. 24
Series RSDG Auto Switch Hysteresis Contact Protection Boxes/CD-P1 1, CD-P12
Do not dispose this fluid in the environment.
(Do not adjust more than 2mm, as it will not be possible to obtain smooth acceleration and deceleration.) Do not adjust based on the stopper's movement, as this can cause cylinder damage. Stroke Adjustment Loosen the round head Phillips screws, and remove the top covers and dust covers (4pcs.).
Note 2) The output functions operate only for the real-time flow rate display, and do not operate for the accumulated flow display. Note 3) Window comparator mode Since hysteresis is 3 digits, separate P1 and P2 by 7 digits or more. 1 digit is the minimum setting unit (refer to the table above).
Note 2) The output functions operate only for the real-time flow rate display, and do not operate for the accumulated flow display.
Single action positive operation X View M A Automatic / Manual change-over screw (Built-in bleed restriction) Sensitivity adjusting screw (Adjusts GAIN) Stopper screw (Do not move) (15) Diaphragm valve SUP OUT2 OUT1 X (1) Pilot valve Supply valve A Supply valve B (8) Feedback lever (9) Span adjusting lever (7) Exhaust valve Span adjusting lever shaft EXH. (4) Counter weight Diaphragm For
Before piping and screwing in couplings, please make sure that sludge trom pipe threading and sealing materials do not go into the pipe. When seal tape is used, tape winding should be done so that 2 threads are left untaDed on the end.
Please make sure that operating conditions do not cause problems since the use of FEP tubing under chemical environment is unsecured.
Orifice size Electrical entry Orifice diameter 2mm 3mm 4mm 5mm 7mm Class 4 Class 3 Class 2 Symbol 2 3 4 5 7 Voltage G C T TL D DL DO Grommet Conduit Conduit terminal Conduit terminal with light DIN connector DIN connector with light 1 2 3 4 5 6 100VAC 200VAC 110VAC 220VAC 24VDC 12VDC For DIN connector (without connector) All are equipped with surge voltage suppressor.
D -DIN connector DL -DIN connector with light DO-For DIN connector (without connector) Orifice and port size combinations T -With conduit terminal TL-With conduit terminal/light Class Orifice diameter Port size 2 3 4 5 7 10 1/8 (6A) 2 1/4 (8A) 1/4 (8A) 3 3/8 (10A) 1/2 (15A) Connector 1/4 (8A) 3/8 (10A) 4 All class B coils are equipped with surge voltage suppressor.
Specifications Air, Nitrogen Fluid 100 to 0kPa (-14.5 to 0psi) Operating pressure 0.5MPa (72.5psi) Withstand pressure 0 to 60C (32 to 140F) (with no freezing) Operating and ambient temperature range 10m Filtration degree Element differential pressure resistance 0.15MPa (21.75psi) Applicable tubing material Nylon, Soft nylon, Polyurethane, Soft polyurethane Symbol Note) Do not use in a line
Do not use any cable other than this cable. 16
Wiring Power supply and N/A communication connector Power LED Communication LED Fig.1 Display and Communication * Please don't do the insert and remove of live-wire after the power supply is turned on. It causes the communication abnormality with the master by the situation.
(Default value : 100%2.00MPa) (Note3) Do not input the signal as like output the pressure of more than 100%. Please use in a range of rating. (Note4) The difference between F_1 and F_2 is adjustable in a range of 10% of the rated value. (Note5) The adjustment like making the relation of F_1 > F_2 is not available.