Modular Type Regulators Series AR Do not use the regulator with flow exceeding the Max. flow indicated in Flow Characteristics as this can cause failure in pressure adjustment. Bleed port 16 Component Parts Handle locking screw No.
Do NOT make upward piping. 2. Float type auto drain (N.C.) 1) Compressor can be used even if energy is under 3.7 kW. 2) Set operating pressure more than 0.15 MPa. 2. Float type auto drain (N.C.) DO NOT pipe upwards. 446 SP093-001I Issued: Sep 2009 P.G.
Note 1) Do not use the power supply of inrush current prevention type for the controller power supply. When conformity to UL is required, the electric actuator and controller should be used with a UL1310 Class 2 power supply. 560
Please do not use it in this fashion. 3. An F.R.L. unit shipped from the plant has its model number labeled. However, components that are combined together during the distribution process do not have a label on them.
Do not service or attempt to remove product and machinery/equipment until safety is confirmed. 1. The inspection and maintenance of machinery/equipment should only be performed after measures to prevent falling or runaway of the driven objects have been confirmed. 2.
Do not apply an impact or large forces to a pad when adsorbing a workpiece. This will cause deformation, cracking and wear of the pad to be accelerated. The stiffening ribs, etc. should touch lightly, while staying within the pad skirt's deformation range. Positioning should be performed accurately.
MB1 R: Rod side, H: Head side Cylinder sizes 80 and 100 do not have basic (without trunnion mounting female thread), rod trunnion and head trunnion types. Foot, ange and clevis types of cylinder sizes from 20 to 63 do not have trunnion mounting female thread. Operate the cylinder within the allowable kinetic energy.
Confirm that the sockets do not protrude from the windows on the side of the receptacle housings. Mounting screw Socket Mounting bolt VQ7-6: M5 VQ7-8: M6 Proper tightening torque (Nm) 0.08 to 0.12 Coil Receptacle Window 3-10-2 Series VQ7-6/7-8 Precautions 2 Be sure to read before handling. For Safety Instructions and Solenoid Valve Precautions, refer to page 3-13-2.
Do not replace the bushings. The bushings are press-fit. To replace them, they must be replaced together with the cover assembly. 2. To replace a seal, apply grease to the new seal before installing it. If the cylinder is put into operation without applying grease to the seal, it could cause the seal to wear significantly, leading to premature air leakage. 3.
Do not service or attempt to remove product and machinery/equipment until safety is confirmed. The inspection and maintenance of machinery/equipment should only be performed after measures to prevent falling or runaway of the driven objects have been confirmed.
Do not supply or discharge air suddenly. This will cause the temperature to decrease due to air expansion, and the temperature may exceed the operating temperature limit of the air tank. If flow speed becomes faster, a loud noise may be generated by the friction inside the tube.
Do the drain pulling out regularly.
2 3 L0 V 4 C/Q (IO-Link)/1(SIO) -17No.PS-OMV0003CN-G NPN 2 DC(+) OUT1 OUT2 DC(-) PNP 2 DC(+) OUT1 OUT2 DC(-) IO-Link L+ C/Q IO-Link DO L-18No.PS-OMV0003CN-G [] 3 0.2 [] / UP DOWN OUT1 OUT1 OUT2 OUT2 [F10]30 () SET 1~3 SET 3~5 SET [] [] [] [3 ] (25 ) (55 ) (23 ) (21 ) 30 () 3 -19No.PS-OMV0003CN-G ON OFF ON P_1 H_1 ON OFF ISE70 ISE71 [P_1] OUT1[MPa] 0.500 0.800 [
.(5%) (0~1MPa 0.001MPa 1/1000) () () F () ripple -14No.PS-OMV0008CN-E ( M46L(2)) 0.760.1 Nm A(ZS-50-A) A M4X6L B(ZS-50-B) B M4X6L -15No.PS-OMV0008CN-E 1.50.1 Nm (ZS-48-A) -16No.PS-OMV0008CN-E -02-N02 8~12 Nm -F02 4~5 Nm 24 () -17No.PS-OMV0008CN-E ()336 336 -18No.PS-OMV0008CN-E FG M12 M12 (Port Class A) 1 DC(+) DC1224 V 2 OUT2 2 3 DC(-) 0 V 4 OUT1 1 IO-Link 1 L+ DC1830 V 2 DO
Do not replace the non-rotating guide. Since the non-rotating guide is press fitted, the entire cover assembly needs be replaced instead of a single part. 37
Do not replace the non-rotating guide. Since the non-rotating guide is press fitted, the entire cover assembly needs be replaced instead of a single part. 38
You do not need to specify "N" (i.e., without lead wire) for D-A3A, D-A44A, D-G39A, and D-K39A. This is the only standard specification automatically available for these models.
Note 3) Do not add value to long stroke models. 4 Compact Cylinder Series CQS Accessories Single knuckle joint Double knuckle joint ND hole H10 axis d9 L MM MM NDH10 RR1 RR1 E1 E1 NX NZ A1 U1 L1 A1 U1 NX L1 A A Metric Threads Metric Threads ND H10 NX Pin part No. NDH10 NX Bore size (mm) Bore size (mm) E1 A1 MM U1 Part No. A Part No.
DC () Blue D-F9PW D-Y7PW D-F9P D-Y7P DC (+) Brown DC (+) Brown OUT Black OUT Black DC () Blue DC () Blue Indicator light ON D-F9BW D-Y7BW D-F9B D-Y59B OUT (+) Brown OUT (+) Brown Operating range OFF Red Green Indicator Red Optimum operating position OUT () Blue OUT () Blue Contact Protection Box/CD-P1 1, CD-P12 Internal circuit
Contact Protection Box/CD-P11, CD-P12 The D-Z7, D-Z8 and D-A9 type switches do not have built-in contact protection circuits. Use a contact protection box in cases such as with an induction load, when the lead wire is longer than 5m or with 100VAC. 1 Operating load is an induction load. 2 Wiring to the load is 5m or longer.