SI unit for EtherCAT 2000 [mm] 03 3000 [mm] 05 5000 [mm] 10 10 [mm] Item Specifications Connector M12 Straight RJ45 Cable O.D. 6.4 mm Nominal cross section AWG26 Min. bending radius (Fixed) 26 mm (4) Seal cap Part number: EX9-AWTS This cap is used to protect the M12 connector opening when the connector is not used.
Discharge capability -P.9 to 10 8. Troubleshooting P.11 to 12 9. Construction and operating principle -P.13 10. Operating principle P.13 11. Sensor mounting (leakage sensor) P.14 1 Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage.
P.1320 16 / 17 3. 3-1. 1 2 3 4 5 6 7 8 9 10 3-2. 2040 50100 18 3-2-1. 02 50 3-2-2. 1 6 2 7 6. 7. 3 19 3-2-3. GR-S-010(10g )GR-S-020(20g ) (XC85,X446)P25 1 2 3 4 8 1 100 83(g) L100mm 1 2 1mm 8. 8. g 20 25 32 40 100st 2 3 3 34 50st 0.5 0.5 0.5 1 20 3-2-4. 1) 8, 9 2 ( 8,) 10 3( 8,) 1mm 9. 10. 3-3.
Replace pilot valve assembly. (10) Protect the valve so that water does not splash the coil. (11) To remove foreign matter,air blow piping, then replace valve.
Dynamic viscosity [m2/s] Viscosity [Pas] Density [kg/m3] Formulas below can be used for common units 1cP = 1mPas = 10-3Pas 1cSt = 1mm2/s = 10-6m2/s 13 Working Principle 1. When air is supplied, it passes through the switching valve and enters drive chamber B. 2.
Dynamic viscosity [m2/s] Viscosity [Pas] Density [kg/m3] Formulas below can be used for common units 1cP = 1mPas = 10-3Pas 1cSt = 1mm2/s = 10-6m2/s Pulsation Attenuating Capacity The process pump generates pulsation because it discharges a liquid using two diaphragms.
Install it above 0.6m from the floor. 9 Maintenance 10 Troubleshooting 6 Operation Continued 6 Operation Continued 9.1 Daily Check 10.1 Alarm list No. Modes Function Selectable Setting Default No.
Node address setting, Communication speed setting 1) Turn on (SW mode) the switch No. 10 of the 10-digit switch mounted on the SI unit. 2) Change the instance attribute value via the network as indicated below.
External pilot air LVC Lubrication Temperature Not required (Use turbine oil Class 1 ISO VG32, if lubricated.) 5 to 60C LVA No freezing LVH LVD Graph (1) VND 02 D Pilot Pressure (N.O. type) JIS Symbol Valve type Valve size N.C. N.O. Normally closed Normally open LVQ 0.7 12 (P1) 10 (P2) Pilot pressure should be within the range of A against the operating pressure.
Cautions 10 7. Maintenance 11 8.
Checks and Inspection Hose Circulating pump Water quantity 20 to 30 L/min Pressure 0.1 to 0.3MPa 0. 10. 3 2030 L/m i n Fig. 2 ( ) Tank (drum can, etc.) b) Operation procedure when a cooling tower is used 1. If a cooling tower is used, supply the cleaning liquid and circulate it for a certain amount of time. 2.
Specifications 10 4. Product outline 10 5. Troubleshooting 11 6. Construction and parts 1112 1 - Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage. These instructions indicate the level of potential hazard with the labels of Caution, Warning or Danger.
Otherwise, the guide parts has twisted and lead to a malfunction. -10- 10) Mount in locations where maintenance will be easy.
Option Rated voltage Voltage symbol Part no. 100 VAC 100V VK300-82-2-01 110 VAC 110V VK300-82-2-03 200 VAC 200V VK300-82-2-02 Note) When requiring a gauge different than that mentioned above, specify the model number. 220 VAC 220V VK300-82-2-04 Option is packed with it.
If the total lifting height is required instead of the discharge pressure, a discharge pressure of 0.1 MPa corresponds to a total lift of 10 m. Selection procedures: 1. First mark the intersection point for a discharge rate of 27 L/min and a discharge pressure of 0.25 MPa. 2. Find the pilot air pressure for the marked point.
) Fittings (4 pcs.): DL10-02 P 250 700 200 600 176 Conditions Supply air pressure: 0.5MPa Load ratio: 50% 90 elbow: 4 pcs.
The fluctuation of the power supply voltage should be kept within +/-10% of the rated voltage. Refer to 5.2 Reset of protective equipment and reset the protective circuit. The fluctuation of the power supply voltage is too large. When the cooling water is not flowing, the compressor for refrigeration has stopped with the lamp lit up. Water-cooled condenser is dirty.
[Load: 10 N or less] Turning without pushing can cause damage to the manual override and trouble such as air leakage, etc. Manual Override Switch Operation For manual override operation, move the manual override switch to a position where letters A and B can be seen.
Bracket, gauge and switch assembly (optional) 10 6. Panel mounting 11 7. Troubleshooting 12 8. Dimensions 13 to 14 -1- Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage.