SI unit for DeviceNet TM Node address setting, Communication speed setting 1) Turn on (SW mode) the switch No. 10 of the 10-digit switch mounted on the SI unit. 2) Change the instance attribute value via the network as indicated below.
External pilot air LVC Lubrication Temperature Not required (Use turbine oil Class 1 ISO VG32, if lubricated.) 5 to 60C LVA No freezing LVH LVD Graph (1) VND 02 D Pilot Pressure (N.O. type) JIS Symbol Valve type Valve size N.C. N.O. Normally closed Normally open LVQ 0.7 12 (P1) 10 (P2) Pilot pressure should be within the range of A against the operating pressure.
Cautions 10 7. Maintenance 11 8.
Checks and Inspection Hose Circulating pump Water quantity 20 to 30 L/min Pressure 0.1 to 0.3MPa 0. 10. 3 2030 L/m i n Fig. 2 ( ) Tank (drum can, etc.) b) Operation procedure when a cooling tower is used 1. If a cooling tower is used, supply the cleaning liquid and circulate it for a certain amount of time. 2.
Specifications 10 4. Product outline 10 5. Troubleshooting 11 6. Construction and parts 1112 1 - Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage. These instructions indicate the level of potential hazard with the labels of Caution, Warning or Danger.
Otherwise, the guide parts has twisted and lead to a malfunction. -10- 10) Mount in locations where maintenance will be easy.
Option Rated voltage Voltage symbol Part no. 100 VAC 100V VK300-82-2-01 110 VAC 110V VK300-82-2-03 200 VAC 200V VK300-82-2-02 Note) When requiring a gauge different than that mentioned above, specify the model number. 220 VAC 220V VK300-82-2-04 Option is packed with it.
If the total lifting height is required instead of the discharge pressure, a discharge pressure of 0.1 MPa corresponds to a total lift of 10 m. Selection procedures: 1. First mark the intersection point for a discharge rate of 27 L/min and a discharge pressure of 0.25 MPa. 2. Find the pilot air pressure for the marked point.
) Fittings (4 pcs.): DL10-02 P 250 700 200 600 176 Conditions Supply air pressure: 0.5MPa Load ratio: 50% 90 elbow: 4 pcs.
The fluctuation of the power supply voltage should be kept within +/-10% of the rated voltage. Refer to 5.2 Reset of protective equipment and reset the protective circuit. The fluctuation of the power supply voltage is too large. When the cooling water is not flowing, the compressor for refrigeration has stopped with the lamp lit up. Water-cooled condenser is dirty.
[Load: 10 N or less] Turning without pushing can cause damage to the manual override and trouble such as air leakage, etc. Manual Override Switch Operation For manual override operation, move the manual override switch to a position where letters A and B can be seen.
Bracket, gauge and switch assembly (optional) 10 6. Panel mounting 11 7. Troubleshooting 12 8. Dimensions 13 to 14 -1- Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage.
Fastening torque recommended: 10+/-2Nm 5-6. Start of operation Before actual operation, confirm there is no leakage. If there is leakage, remove the element after stopping the operation. Clean the seating surfaces, check and replace the O-ring and tighten the cover. -10- Doc. No. SF-OMZ0013-B 6. Dimensions -11- Doc. No. SF-OMZ0013-B Revision history Rev.
-01 G43-P10-N01-X30 02:1/4 03:3/8 04:1/2 Rc FG NNPT 00.010.2MPa 10.010.4MPa 20.010.8MPa PRECI SI O N REG U LATO R I R302BG No.
No.VFR2000-OMM0001 5 VFR2000 / / / / -2,3 -4 -5 -5 -6 -6 -6 -7 -7 -7 -8 -9 -9 -9 -10 3 -10 -10,11 DIN / -11 -11 -12,13 -14,15 -1No.VFR2000-OMM0001 ISO/IEC) (JIS) 1) 2 *1) ISO 4414: Pneumatic fluid power -General rules relating to systems ISO 4413: Hydraulic fluid power -General rules relating to systems IEC 60204-1: Safety of machinery -Electrical equipment of machines
(1) (2) (3) 2(A)3(R)() (4) (5) 3(R) (6) 2(A)() (7) (8) (9) (10) (11) (12) 1 (ISO VG32) (13) 3(R) (14) (15) (16) (17) (18) (19) (20) (21) (22) 1. 2. 3. 4. 5. 6. 7. * 12 VEX-OMV0001 : VW 4-14-1, Sotokanda, Chiyoda-ku, Tokyo 101-0021 JAPAN Tel: + 81 3 5207 8249 Fax: +81 3 5298 5362 URL http://www.smcworld.com Note: Specifications are subject to change without prior notice