SI unit for DeviceNet ® Safety Instructions Warning Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use.
1 SPEED Forward speed switch 16 forward speeds are available. !2 Reverse speed switch 16 reverse speeds are available. !3 ACCEL Forward acceleration switch 16 forward acceleration steps are available. !4 Reverse acceleration switch 16 reverse acceleration steps are available. !5 CN1 Power supply connector Connect the power supply cable. !
1 i o w Mounting e Bore size r Port thread type t Cylinder stroke [mm] q With auto switch 12 12 mm 16 16 mm 20 20 mm 32 32 mm 40 40 mm 50 50 mm B Through-hole A Both ends tapped Nil M thread 12, 16 Rc 20 to 50 TN NPT TF G F Built-in One-touch fittings*2 Nil Without magnet for switch*1 12 10 16 10, 15 20 10, 15, 20 32 10, 15, 20 40 20, 25, 30 50 20, 25, 30 D With auto switch (Built-in magnet
The cartridge assembly cannot be inserted while the locking knob is in the LOCK position, attempting to do so may cause damage. Do not directly touch the emitters with your finger or tools. This may result in injury.
Do not touch the inside of the driver and its peripheral 16. Do not install the product in an environment under the devices. It may cause an electric shock or damage to the driver. effect of vibrations and impacts. It will cause failure or malfunction. 2. Do not perform the operation or setting of the product 17. When a surge generating load such as a relay or solewith wet hands.
ATEX Intrinsic Safety Type of Explosion Protected Construction 16 Explosion Protected Construction Rate 16 Wiring 16 Barrier 17 Description of Components 18 Contents of LCD Display 18 Initial Adjustment 19 Change of Parameters for Initial Operation 19 Initial Adjustment 19 1.Selection of calibration mode 19 2.Check angle of feedback lever 20 3.
Safety Instructions Warning Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. Do not operate or set with wet hands. This may lead to an electric shock. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result.
Do not let water, cutting oil or dust splash on the equipment. It can cause oil leakage and malfunction of the shock absorber. RB J D-X 20Data 10-9-15 15 10-9-16 16 Stopper Cylinder Series RSA 50, 63, 80 RE A B Stops pallets gently. Stopper cylinder with built-in shock absorber.
Do not allow pallets to strike the lever when it is standing up. Do not allow pallets to strike the lever when it is standing up (after the shock absorber has absorbed energy), because the cylinder body will be subjected to the full energy of the impact. 2. Do not use a stopper cylinder for intermediate stopping of loads directly connected to a cylinder, etc.
List of Parameters for each Mode .16 4.1 Parameters common to each mode . 16 4.2 Position control mode . 16 4.3 Speed control mode . 17 4.4 Torque control mode . 17 4.5 Positioning mode . 18 5.
Do not use in an environment where corrosive gases, chemicals, sea water, water or steam are present. Refer to the construction drawings regarding the air chuck materials. 2. Do not use in direct sunlight. 3. Do not operate in a location subject to vibration or impact. 4. Do not mount the product in locations where it is exposed to radiant heat. 5.
Please do not over monitoring the cushion effect.
Do not use in an environment where corrosive gases, chemicals, sea water, water or steam are present. Refer to the construction drawings regarding the air chuck materials. 2. Do not use in direct sunlight. 3. Do not operate in a location subject to vibration or impact. 4. Do not mount the product in locations where it is exposed to radiant heat. 5.
Do not operate at pressures or temperatures, etc., beyond the range of specifications, as this can cause damage or malfunction. (Refer to the specifications.)
Safety Instructions Warning Do not disassemble, modify (including changing the printed circuit board) or repair. Do not use the components other than the specified components. An injury or failure can result. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result.
Safety Instructions Warning Do not disassemble, modify (including changing the printed circuit board) or repair. An injury or failure can result. Do not operate the product outside of the specifications. Do not use for flammable or harmful fluids. Fire, malfunction, or damage to the product can result. Verify the specifications before use.
Do not make any modifications to be product. Do not take the product apart. Piping Caution 1. Before piping Make sure that all debris, cutting oil, dust, etc, are removed from the piping. 2. Wrapping of pipe tape When screwing piping or fittings into ports, ensure that chips from the pipe threads or sealing material do not get inside the piping.
Failure to do so may cause the angle adjusting screw to become loose or drop.
/O.D. mm Series Body size 6.5/10 8.5/12.5 5/8 6/9 8/12 11/16 KK3 KK4 KK6 1/8 1/4 1/2 One-touch fitting type Applicable tubing O.D. mm Series Body size 16 8 10 12 4 6 KK3 KK4 KK6 1/8 1/4 1/2 Manufactured by Rectus Series KK13 Series KK13 Applicable hose I.D.