SMC Corporation of America
Elite Part Number Search
Search Results "HRS200-AN-46-AS"

Take measures to ensure air quality, such as by installing an aftercooler, air dryer, or water separator. Compressed air that contains a large amount of drainage can cause malfunction of pneumatic equipment such as air grippers. Therefore, take appropriate measures to ensure air quality, such as by providing an aftercooler, air dryer, or water separator. 4.

[Tips] AN-> A set of thread adapters that converts the connections from Rc to NPT is enclosed as an accessory. For NPT thread, be sure to use this adapter. A set of thread adapters that converts the connections from Rc to G is enclosed as an accessory. For G thread, be sure to use this adapter.

Model number: HRR010-AN/WN-10/20 The transition connector from Rc to NPT is enclosed as an accessory. For NPT piping, be sure to use this connector. Model number: HRR010-AF/WF-10/20 The transition connector from Rc to G is enclosed as an accessory. For G piping, be sure to use this connector.

Model number: HRR050-AN/WN-20/40The transition connector from Rc to NPT is enclosed as an accessory. For NPT piping, be sure to use this connector. Model number: HRR050-AF/WF-20/40The transition connector from Rc to G is enclosed as an accessory. For G piping, be sure to use this connector.

Auto switch operating range (mm) Time load applied (ms) x 1000 V (mm/s) = In cases of high piston speed, the use of an auto switch (G5NTL) with a built-in OFF delay timer ( 200 ms) makes it possible to extend the load operating time. 2. Keep wiring as short as possible.

Take measures to ensure air quality, such as by installing an aftercooler, air dryer, or water separator. Compressed air that contains a large amount of moisture can cause malfunction of pneumatic equipment such as rotary tables. Therefore, take appropriate measures to ensure air quality, such as by providing an aftercooler, air dryer, or water separator. 4.

(The motor rotates in the reverse direction if the table hits an obstacle such as the end stop damper.) Take the motor phase detection step into consideration for the installation and operation of this actuator. Caution 1. Keep the controller and product combined as delivered for use. The product is set in parameters for shipment.

Do not use the product in; Food zone: An environment in which foods directly get into contact with the cylinder, and the food will be handled as a commodity. OK to use the product in: 17.4. Splash zone: An environment in which foods can directly contact the cylinder, but the food that has contacted the cylinder will not be handled as a commodity.

The purpose of an air cushion is not to reduce the speed of a piston as it nears the stroke end.

Environment at an altitude of 1000 meters or higher Heat radiation and withstand voltage will decrease. Contact SMC for details. (2) Do not use in an environment where the product is directly exposed to liquid, such as cutting oils.

Environment at an altitude of 1000 meters or higher Heat radiation and withstand voltage will decrease. Contact SMC for details. (2) Do not use in an environment where the product is directly exposed to liquid, such as cutting oils.

This system should not be applied with an undue force such as caused by piping installation.

LC7 LC8 5-point stoppable type (2-point for both ends and 3-point for an intermediate stop) 5-point positioning is possible at any preferred locations. 3-point stoppable type 5-point stoppable type (with streamer) LXF LXP Stop command by an external input such as a PLC or PC makes it possible to decelerate or stop a slider (as programmed).

How to Order Type 46 (5 Port/Base mounted) Applicable solenoid valve SYJ340SYJ343SS5YJ3 46 05 M5 Type 46 Type S46 ( ) Single solenoid coil is on same side as the A, B port. M5 x 0.8 R1 R2 port Applicable blanking plate assembly SYJ3000-21-2A Stations Valve mounting direction 02 2 stations Single solenoid coil is on opposite side as the A, B port.

How to Order Type 46 (5 Port/Base mounted) Applicable solenoid valve SYJ340SYJ343SS5YJ3 46 05 M5 Type 46 Type S46 ( ) Single solenoid coil is on same side as the A,B port. M5 x 0.8 R1 R2 port Applicable blanking plate assembly SYJ3000-21-2A Stations Valve mounting direction 02 2 stations Single solenoid coil is on opposite side as the A,B port.