EX600-SEN3_4_eng Please keep this manual handy for future reference. 11 Connect the M12 connector cable. The M12 SPEEDCON connector connection method is explained below. (1)Align mark B on the metal bracket of the cable connector (plug/socket) with mark A. 7 10 8 1 9 (2)Align with mark C on the unit and insert the connector vertically.
(PORT2) 11 The power supply for output is properly. Green ON PWR(V) The power supply voltage for output is below 19 VDC. (When diagnostic parameter is enabled) Red ON Assembly Either of the following conditions are detected: The unit has not been configured correctly. The PLC is idle state.
Please keep this manual handy for future reference. 11 Connect the M12 connector cable.
PWR(V) 11 Connect the M12 connector cable. The M12 SPEEDCON connector connection method is explained below. (1)Align mark B on the metal bracket of the cable connector (plug/socket) with mark A. 7 10 8 SF Displays the system status. 1 9 BF Displays the communication status. (2)Align with mark C on the unit and insert the connector vertically.
(PORT2) 11 Sink/NPN (Positive common) Source/PNP (Negative common) Output type Assembly Setting and Adjustment 32 outputs Number of outputs Output CAUTION indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury.
Check if the dispersion is within the indication accuracy range. 11 Product failure Replace the product. Install a 5 m filter to prevent foreign matter from getting into the pressure port. Also, clean the filter regularly to prevent drainage deposits. Foreign matter Check if foreign matter has entered the pressure port. Rework the piping.
DC1224 V DC1224 V 8 DC(+) DC(-) DC1224 V DC1224 V DC(+) 9 DC(-) / / 10 ( ) 11 / 5m / 12 2030 20 -28No.PS-OMG0001CN-H No.
If product is to be used in a public place, ensure product is not directed at people or used in a manner that could adversely affect the environment. 10.For other cautions, refer to the 2 Port Solenoid Valves for Fluid Control Precautions. 11.
O O 12 13 14 7 VN-OMP0002 No. 1 2 3 4 5 , 6 7 8 9 10 11 P2N.C.
For details, refer to the catalog Precautionary measures against condensation in a pneumatic system (CAT.P-E01-11). 2-6.
Refer to SMC Compressed Air Cleaning System for the details of compressed air quality described above. 11 25 Piping ! Caution 1Preparation before piping. Thoroughly flush the fittings to prevent dust or chips from entering the gripper.
D-M9/ M9W/ Y59/ Y7P/ Y7W D-M9/ M9W/ Y59/ Y7P/ Y7W D-M9 D-M9V L (mm) D-M9 D-M9W D-M9V D-M9WV D-M9A D-M9AV MHY2-10D 3 1 5 3 MHY2-16D 3 1 5 3 MHY2-20D 3 1 MHY2-25D 1 ) 11 8. 1 2 ON ON 1 1),2)1 A 2 B 1),2) C 1 1 12 2) 3) 4) 0.30.5mm 2) 0.30.5mm 0.30.5mm 0.30.5mm 13 2-4. 1.
M8 8 P .18 M8 8 () NPN PIN 1 +24V DC24V 2 3 4 5 ON/OFF 6 ON/OFF 7 8 GND DC0V M8 2 M8 1 11 - 3-7. Z Y Y X Z Z X X Y Z -0.4 -0.8 48.4 12 - 4 (www.smcworld.com) 4-1.
JMHZ2-16D-X7400B-HC10-(*) P13P14P15 4 M6 31.5 2XM4x0.7 8 4 M6 108.8L 4 4 M4 4 M3 27 17 10 - JMHZ2-16D-X7400B-HC10DT-(*) 4 M6 32.5 8 4 M6 109.8L 4 4 M4 4 M3 27 17 11 - 3-6. M8 8 M8-Molex P .19 NPN PNP No. 1 +24V DC24V 2 GND DC0V 3 ON/OFF() 4 ON/OFF() 5 () 6 () 7 8 Molex (51227-0800) M8 8 12 - 3-7.
We do not guarantee against any damage if the product is used outside of the specification range. 11. Energizing for extended periods of time Caution hot surface Be aware that the valve surface may get hot. If a valve is continuously energized for an extended period of time, the temperature of the valve will increase due to the heat generated by the coil.
If this occurs, stabilize the ambient temperature and fluid temperature properly. -11- 6.
Drawings 11 Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage. These instructions indicate the level of potential hazard with the labels of Caution, Warning or Danger.
Implement measures to prevent any danger from occurring when operating the actuator. 11. Ventilation 2. Actuator drive When an actuator, such as a cylinder, is to be driven Provide ventilation when using a valve in a confined area, such as in a closed control panel.
Electroless nickel plate treated is available as option -X2. 11 4. Troubleshooting M series miniature fitting cannot be disassembled or repaired in order to quality maintenance. When failure such as "Insufficient sealing" occurs, please replace the whole product. 12 5.
Panel mounting 11 7. Troubleshooting 12 8. Dimensions 13 to 14 -1- Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage.