Cooling Capacity: 300 (28 kW), Thread: N (NPT, w/Rc-NPT Conversion Fitting), Option: AK (A + K)
Cooling Capacity: 300 (28 kW), Thread: N (NPT, w/Rc-NPT Conversion Fitting), Option: K (w/Fluid Fill Port)
Cooling Capacity: 300 (28 kW), Thread: N (NPT, w/Rc-NPT Conversion Fitting), Option: AKW (A + K + W)
Cooling Capacity: 300 (28 kW), Thread: Rc, Option: AK (A + K)
Cooling Capacity: 300 (28 kW), Thread: N (NPT, w/Rc-NPT Conversion Fitting), Option: A (w/Caster Adjuster-foot)
Cooling Capacity: 300 (28 kW), Thread: N (NPT, w/Rc-NPT Conversion Fitting), Option: AW (A + W)
Cooling Capacity: 300 (28 kW), Thread: Rc, Option: A (w/Caster Adjuster-foot)
Cooling Capacity: 300 (28 kW), Thread: N (NPT, w/Rc-NPT Conversion Fitting), Option: KM (K + M)
Cooling Capacity: 300 (28 kW), Thread: N (NPT, w/Rc-NPT Conversion Fitting), Option: AKMW (A + K + M + W)
Cooling Capacity: 300 (28 kW), Thread: F (G, w/Rc-G Conversion Fitting), Option: AKM (A + K + M)
Cooling Capacity: 300 (28 kW), Thread: N (NPT, w/Rc-NPT Conversion Fitting), Option: AKM (A + K + M)
Please contact us for the latest version.sales@ocaire.com, L-BLOCK ASSY, NBR, JPN SPL, OTHERS, FHG HYDRAULIC FILTER, 28, FHG OTHER SIZE JPN SPECIAL
Please contact us for the latest version.sales@ocaire.com, L-BLOCK ASSY, FKM, JPN SPL, OTHERS, FHG HYDRAULIC FILTER, 28, FHG OTHER SIZE JPN SPECIAL
Please contact us for the latest version.sales@ocaire.com, BASE CYLINDER, ACTUATOR, CG5 CYLINDER, STAINLESS STEEL, SD, 100MM CG5 DOUBLE-ACTING, 28 lb
AC Servo Motor Driver (MECHATROLINK-II type) For safety , use the external Regenerative resistors with thermoswitches. 28 - 5. Trial Operation (SigmaWin+) The procedure of the test driving with setup software (SigmaWin+) is shown below. When use the setup software (SigmaWin+), order USB cable (LEC-JZ-CVUSB) separately. 5.1 Communications setting for PC When SigmaWin+ is initially started, the Connect dialog box appears.
After the DRIVERs have been successfully connected to SigmaWin+, a list of the connected DRIVERs will appear on the screen. 28 - DRIVER Selection Box 3. Select the DRIVER to be connected and then click Connect, or just double-click the DRIVER to be connected. The SigmaWin+ main window will appear.
If necessary, re-application of power supply should be done when 5s or more passes after PWR indicator lamp goes off. 28 3.Stroke learning General 3 positions 5 positions General 3-1 By push of over 3s at least, the product comes into learning mode and starts stroke learning. 3-2 Confirm 2 indicator lamps MOTOR and END are blinking.
Therefore the INF output may be activated when the pushing force differs from the set "Thrust Setting Value". 28 - INFP signal The output turns ON when the current Card Motor table position is within the positioning repeatability range (LAT3 is 0.09 mm, LAT3F is 0.005 mm) of the target position. The output conditions for each operation mode are similar to those for the INP signal.
Pulse train signal specifications (Open collector input and differential input are common) 5 s or more 24 V 21.6 V to 26.4 V 5 V 4.75 V to 5.25 V PP3s or less 5 s or more 3s or less 16 s or more 28 - 7.4 Parallel I/O signals (Pulse Input Type) (1) Input side (Pulse input type) Function Description Common terminal for the input signal power supply.
Tightening torque: 28 to 30Nm Note 2) If the amount of drainage flowing into the heavy duty auto drain is small, open the bleed valve gradually to adjust so that the drainage can flow into the auto drain smoothly. 10.4 Maintenance 1) Check the auto drain condition at least once a day.