PAB-OM-C006-B Replacement parts PAB-OM-C006-B P2 FLUID IN FLUID OUT P1 IN FLUID PT F E diaphragm set K T PA 3 3 1 S w itching valve assembly set K T PA 3 3 6 FLUID OUT P2 P1 4 . Maintenance 3 . How to use C aution Quality of supply air Place filter w ith filtration 5 m.
Replacement parts PAB-OM-C007-B P2 FLUID FLUID OUT IN P1 PT F E diaphragm set K T PA 5 3 1 S w itching valve assembly set K T PA 5 3 6 FLUID IN FLUID OUT P2 P1 4 . Maintenance 3 . How to use E xternal leakage of transported fluid F luid might leak externally due to life of diaphragm, and this could result in human injury or equipment damage. T ake measures against leakage.
Standard (with round type pressure gauge) (Pressure gauge port size) (Port size) Panel mounting dimensions Plate thickness AR20/30-D: Max.3.5 AR40-D: Max.5 Dimensions Optional specifications Standard specifications Round type pressure gauge (Semi-standard: Z) Round type pressure gauge (with color zone) Round type pressure gauge Model M281 P1 P2 J K J H J J AR20-D 1/8 40 66.8 26.5 21 21
round type pressure gauge) Panel mounting dimensions Round type pressure gauge Plate thickness AW20-D, AW30-D: Max3.5 AW40-D : Max5 Center of piping (Pressure gauge (Port size) port size) maintenance Clearance for Dimensions Optional specifications Model Round type Round type Round type Standard specifications pressure pressure gauge pressure gauge (Semi-standard: Z) (With color zone) gauge P1
Flow characteristics: C Max. operating frequency To CYL port SUP side pressure (P1) Note) Based on JIS B 8375-1981 (Supply pressure: 0.5 MPa) Dimensions Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com Single unit Manifold 21.5 (5) 18 29 10.5 2n-C4, C6 C4: One-touch
Warning Warning Caution External Pilot Pilot port 12(P1) and 10(P2) piping P1 and P2 piping should be as follows according to the model. Installing a silencer to the exhaust port and the bleed port is recommended for noise reduction and for dust entry prevention. Caution Mounting 1. Do not apply external force to the coil section.
Vacuum pressure: P1 Conversely, the size of the ejector or the size of the switching valve of the vacuum pump system can be obtained from the adsorption response time.
As a guide, when W + P0a>P0A, adjust P1 to make W + P1a = P0A. W: Load (N) P0: Operating pressure (MPa) P1, P2: Reduced pressure (MPa) a: Rod side piston area (mm2) A: Head side piston area (mm2) Warning Since CJ2X, CUX10 are subject to internal leakage due to their construction, the speed may not be fully controlled with the meter-out controller () during low speed operation.
Normal primary pressure Drop of primary pressure Increase of primary pressure Pressure P1 P2 Time Switch output 1, 2 ON OFF The correction value is not stored on the EEPROM. When auto shift is used: When the primary pressure changes, set the auto shift function to Lo.
Normal primary pressure Drop of primary pressure Increase of primary pressure Pressure P1 P2 Time Switch output 1, 2 ON OFF Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com The correction value is not stored on the EEPROM.
The air pressure forms a bridge circuit inside the unit with a vacuum applied to the circuit, but with the adsorption nozzle S4 open, adjust needle S2 so that (P1 P2). When parts are absorbed by nozzle S4, the resulting (P2 P1) differential will be detected by the pressure sensor.
(P1 P2) : Upstream pressure (MPa) : Downstream pressure (MPa) : Effective area (mm) : Cv factor Q P P1 P2 S Cv 9 10 Series VCW Safety Instructions These safety instructions are intended to prevent a hazardous situation and/or equipment damage.
O F , < F , Q r '=r, @ r,> r, Pressure Raies (P1 =Primary Pressure) (P2=Secondary Pressure) NVEP3l2O-2 NVEP314O-'r -04 Primary Pressure P1 = 45 PSIG (3 KSI/cmr) E t2 I { t r S F g t o o E 28 (r. a ( 1 ) E a E a NVEHtl4O-1 E t ^ *t 6 S (0.15) (0.s) t . 5 ( 0 1 ) F 5 (0.05) NVEE NVEP CONSTRUCTION DETAIL Flow Raie'lvpo: VEF212O (2 Pdts) NVEF:112O (3 Porb) Pressuro llrp: NVEP3I2O (3 Porb) l l
Fixed orifice and variable throttle are available as a throttle for adjusting the pressure increase. (1, 1.5, 2) Output Pressure (P2) vs Time Graph Output P2 P1 P2 reaches half of P1, and then the main valve of the soft start-up valve turns on.
P1 Parts assembly Parts assembly Degrease/Wash Degrease/Wash P2 P2 Pure water (16M-cm) wash Assembly Time Time Assembly Inspection Circuit diagram Inspection Interior purge P2 P1 2 1 2 1 Interior purge Package SRH Clean booth Class 100 Package 856 Clean Regulator SRH Series ARJ How to Order AR425 to 935 ARX 02 SRH 3 0 0 0 AMR Gauge port orientation ARM Body size 3 4 1/4 3/8 Nil: Standard
VCHRA 30 06 G ARJ AR425 to 935 Body size 30 40 Thread type (ISO1179-1 compliant G thread for hydraulic and pneumatic equipment) AMR ARM Port size Port size VCHRA30 Specifications VCHRA40 Symbol Inlet pressure P1 (MPa) Pilot pressure range ARP 06 10 14 3/4 VCHRA30 Model VCHRA40 1 VCHRA40 PA = 0.171 x P2 + 0.027 x P1 4.0 IR Valve construction Piston type 11/2 Outlet set pressure P2 (MPa) Valve
Q=14.2Cv 10.2 P l/min Formula based on effective area (Smm2) Q=0.8S 10.2P l/min Q P P1 P2 S Cv : Flow rate (l/min) : Pressure differential (P1 P2) : Upstream pressure (MPa) : Downstream pressure (MPa) : Effective area (mm2) : Cv factor 4.5-11 Series VCW 2 Port Solenoid Valve for Fluid Control Be sure to read before handling.
Compact Vacuum Unit Series ZB RoHS How to Order Single Unit 5 L 0 2 K1 ZB 00 P1 C4 Vacuum Pump System 5 L 1 1 K1 ZB 04 P1 C4 Ejector Nominal Nozzle Size Rated Voltage Body Type 5 6 24 VDC 12 VDC Port specification Note 2) Symbol Applicable supply valve and standard supply pressure Body specification Nominal nozzle size Large flow (N.C.)
Note 3) Bowl assembly for the AWM30, AWM40/AWD30, AWD40 comes with a bowl guard (steel band material). 71 Mist Separator Regulator Series AWM20 to AWM40 Micro Mist Separator Regulator Series AWD20 to AWD40 Dimensions M J T N F Panel fitting dimension AWM20 AWD20 D Y U Bracket (Option) W S R IN OUT B C Z Q K V IN OUT AWM20/AWD20: Max. 3.5 OUT 2-P1 (Port size) P2 (Pressure gauge port size)
Note 3) Bowl assembly for the AWM30, AWM40/AWD30, AWD40 comes with a bowl guard (steel band material). 71 Mist Separator Regulator Series AWM20 to AWM40 Micro Mist Separator Regulator Series AWD20 to AWD40 Dimensions M J T N F Panel fitting dimension AWM20 AWD20 D Y U Bracket (Option) W S R IN OUT B C Z Q K V IN OUT AWM20/AWD20: Max. 3.5 OUT 2-P1 (Port size) P2 (Pressure gauge port size)