Series: 2 (VQ20), Stations: 3 Stations, Option: None, Thread: 00N (NPT3/8)
Series: 2 (VQ20), Stations: 6 Stations, Option: None, Thread: 00N (NPT3/8)
Series: 2 (VQ20), Stations: 8 Stations, Option: None, Thread: 00N (NPT3/8)
Series: 2 (VQ20), Stations: 4 Stations, Option: None, Thread: 00N (NPT3/8)
TA301 To prevent malfunctions, do not clog the breathing port. (When mounted on a metal surface, breathing air can go through from the breathing port to the breathing groove; however, when the valve is mounted on a rubber surface, the breathing air may be blocked by the deformation of rubber.) 2.
Make sure that dust and/or other foreign materials do not enter the valve from the unused port (e.g. exhaust port). The grommet portion contains a breather hole for the core.
VQC SQ VQ0 VQ4 Note) Do not pull on the lead wires with excessive force. This can cause faulty and/or broken contacts.
Do not hold the part of sintered metal with a wrench, etc. to tighten. When the main body is made of metal (Except BC element) [Series 25] Within the recommended tightening torque shown in the chart below, use a wrench on the hexagonal flats and tighten. Tightening by using a pipe wrench or pliers may cause damage to the silencer. This method is not recommended. Caution 2.
Valve No. (1st to 4th stations) Blank plate part No. (5th station) VV3Q12-05 VQ110-5L VVQ100-10A-2 Applicable Solenoid Valve (Plug lead style) VQ1l0l-lL VQ1l0l-lM VQ1l0l-lG 1 VQ100 Series Place in front of the part No. of solenoid valve which is to be mounted. Manifold base 2 Plug lead unit Write sequentially from the 1st station on the D side.
Reconfiguring the operation mode, as well as the zero and span adjustments, are easy to do in the field. INSTALLATION A B c D Installation Transmission oin & Feed-back lever Fig. 1 SINGLE.ACTING ACTUATOR OPERATION ACTUATOR SIGNAL RANGE INSTALLATION STYLE (REFFIG. 1) OUT 1 OUT2 Direct ?
Reconfiguring the operation mode, as well as the zero and span adjustments, are easy to do in the field. INSTALLATION A B c D Installation Transmission oin & Feed-back lever Fig. 1 SINGLE.ACTING ACTUATOR OPERATION ACTUATOR SIGNAL RANGE INSTALLATION STYLE (REFFIG. 1) OUT 1 OUT2 Direct ?
Male Connsctor Plug-in Elbow 01 ,/g -/92 05 -/1 07 ,4 1 0 1 1 l l 1 1 3t ' o ' Pr. SAE propoad 3pci{icrto.i, all mal ttr.ad8 wltl incorporEt6 1 3 1; Male Branch Union 'Y" 18 " Note: 1/8 tub sizes ar6 de6onatEd by a KO sdos pad numb6( end arc not covgred undr tho OOt or SAE pcificetions, shce OOT doe not spcity prirmanc Fquiromehls.
(Do not use machine oil or spindle oil ) When bottom mounting, the guide shaft will protrude from the bottom surface Therefore' drill a hole lor a hexagon-holed bolt for mounting and an escape hole for guide shaft on the mounting surface.
NARM 2500 05 A 02 G1 Optimal for central pressure control. Accessory Regulator for manifold Pressure easily set using the new handle. One-touch lock system.
VK300-82-2-01 VK300-82-2-02 VK300-82-2-07 VK300-82-4-51 VK300-82-4-06 VK300-82-3-05 VK300-82-3-53 1578
Release flow rate adjusting needle Ejector exhaust PV/V port size 05 07 0.5 mm 0.7 mm With silencer Port exhaust Rc Common exhaust (Manifold only) 1 Nil Nil Y M5 x 0.8 L Without lock nut 1 8 2 (1) 10 1.0 mm M6 x 1 (Option) With lock nut 3 (2) Vacuum switch electrical entry Note 1) When port exhaust is applied to the manifold, pilot exhaust is done by common exhaust.
Compact Vacuum Ejector Series ZA How to Order Ejector Unit ZA1 1 07 K1 P1 5 L 0 1 Nozzle nominal size Vacuum (V) port 05 07 0.5 0.7 Applicable tubing O.D. Part no. KJS23-M5 KJS04-M5 KJL23-M5 KJL04-M5 Symbol 1 2 4 5 3.2 (Straight) 4 (Straight) 3.2 (Elbow) 4 (Elbow) Solenoid valve combination (Refer to Table (1).)
Also, do not use the filter when these chemicals are present in the atmosphere. 2
clevis type Double clevis type Center trunnion type Front trunnion type 40 50 63 80 100 40mm 50mm 63mm 80mm 100mm Nil J K Nil N R H Without rod boot Nylon tarpaulin Neoprene cloth Both sides Without cushion With front cushion With rear cushion Aluminum tube Rod boot Part nos. for cylinders with built-in magnets Cushion In the case of cylinders with built-in magnets but no auto switches, do
(Do not use machine oil or spindle oil ) When bottom mounting, the guide shaft will protrude from the bottom surface Therefore' drill a hole lor a hexagon-holed bolt for mounting and an escape hole for guide shaft on the mounting surface.