New

G Grommet E NPT Grommet 1E 12 VDC (With surge voltage suppressor) G E G H K L Z 1F NPT 48 VAC 1G 1H 1V 1J Rc 220 VAC 240 VAC E E DIN terminal Special voltage With light Without DIN connector G (With surge voltage suppressor) E E NPT 24 VAC 12 VDC 48 VAC Rc E 1K 1L Note) When the body is resin, one-touch fittings are equipped. 220 VAC 240 VAC Conduit terminal 1M 1W (With surge voltage suppressor

LEC-OM07605CN

PB32 (e)([Pr. PB33][Pr. PB36][Pr. PB56][Pr. PB59])[Pr.

CLA

_(mm) e ,.

A

D I M E N S I O N S S E E N E X T P A G E NCDRB1BW30 P211180-1 NC_R1FW30 P211180-2 M O R E A C C E S S O R I E S S E E N E X T P A G E Courtesy of Steven Engineering, Inc. !

MGP

Note 6) Dimension E' cannot be less than the standard dimension E.

Stopper Cylinder

0 w q e r t u !

MHZ

Flat finger type 3 E Narrow type is not available for 6, 32 and 40.

MHZ

Flat finger type 3 E Narrow type is not available for 6, 32 and 40.

MHF2

4 r t e !6 Parts list Parts list Note Material No. Description No.

MHZ2/MHZJ2

Cylinder bore MHZ2 D E X 7 Cylinder bore MHZ2 D E X46 Not available when equipped with dust cover/MHZJ2.

CEx-OMI0064

NO. 19 NO. , 26 , 41 - 10-2 CEU5 , ROM , , ,SMC RAM , ,SMC 2ROM E ,, , , 2ROM E 2ROM 80 E , , ,SMC , 42 -

SMC Pneumatic Clean Series

Actuator driving system Inside of clean room w t e q r t q Cylinder relief port piping w Solenoid valve exhaust piping e Breathing piping of regulator r Drain piping t Exhaust Cleaner for Clean room/AMP series Cylinder relief port piping Series 10-/12-/21(atmospheric release type) Connect the relief port piping with the dedicated duct piping installed outside the clean room or with the exhaust

•

(3d;git) (3d;git) (3dlgit) (3digit) Fluid Air,noncorrosive gas +3% F.

End Lock Cylinder Series CBM2/ø20, ø25, ø32, ø40 Series CBA1/ø40, ø50, ø63, ø80, ø100 CL MLGC CNA CB CV/MVG Maintains the cylinder’s CXW original position even if the CXS air supply is interrupted. CXT MX

Flange style (20 to 32) Be aware that the cylinder mounting bolts and the fitting could come in contact with each other in the following styles: q Front flange style with the front end lock, w Rear end flange style with the rear end lock, and e With double end lock.

MHY2/MHW2

8 e w !7 t !5 r o !8 e !6 w @0 !7 t !5 r o !8 e !6 w @0 !7 t !5 !0 u !2 i q !1 !4 y !9 !0 u !2 i q !1 !4 y !9 !0 u !2 i q !1 !4 y !9 !3 Open Component Parts Component Parts Note No. q Description Material Aluminum alloy Description Material Note No. Body Bushing B Hard anodized Sintered alloy steel o !0 !1 !2 !3 !4 !5 !

Refrigerated Air Dryer For Use in North, Central and South America

line Dryer The malfunction of air bearings of 3D measurement device, etc. 3 IDFB Series Model Selection Air dryers should be selected based on the corrected air flow capacity while taking operating environment and facility into account.

Air Cylinder/End Lock Series MBB ø32, ø40, ø50, ø63, ø80, ø100

Bore size (mm) 32 40, 50, 63 80, 100 Thread size M2.5 X 0.45 X 25 l M3 X 0.5 X 30 l M5 X 0.8 X 40 l Pulling force 4.9N 10N 24.5N Stroke (mm) 2 3 3 e Release lock when mounting or adjusting the cylinder. If mounting is done with lock engaged, lock mechanism may be damaged. * Remove bolt under normal operations.

CE

c. 6. 1. 7. a.060 b.2585%RH c. d. e. 8. ,, f. g.( 9. ) h. i. j. k. l. 2. 1. 2. 1. 3 2. 1. 3. 4. 1. 12:0.071.0MPa 2063:0.051.0MPa :060 5. 2. 1. 5m 1. 2. 2. 3. F.G. 4. 1. 1. 2. 12 10N [102kgfcm] 1. 2032 20N [204kgfcm] () 40,50,63 30N [306kgfcm] 2. 3. 2. 1.52 1. 2. 1. 1()ISO VG32 3. 4. 5. 6. 1. 2.14.5mT CE1 3. 4. (DC1224V) [] 1. 2. 3. 4. 2.

VP3145/3165/3185

In that case, loosen the screw with washer (3e) and place a lead wire (3d) into the bracket, and then tighten it once again. b Maximum size of crimped terminal (9) is up to 1.25 mm2 3.5 when O terminal.

VT317

Component Parts Operation principles Spool valve w is pushed upward by the return spring e, port P is closed, and port A and port R are opened. Caution 1. Since this valve has slight air leakage, it can not be used for vacuum holding (including positive pressure holding) in the pressure container. Specifications different from standard are as follows.