Compact

Do not drop, apply excessive impact (more than 300m/s2 for reed switch, more than 1000m/s2 for solid-state switch) when handling. Damage could occur to the inside as well as the body. 2.Do not pull the lead wire wiih excessive force. Do not pull the lead wile to move the cylinder.

AC Servo Motor Driver LECYM/LECYU Series Compatible LEF  Position control, speed control and torque control Power supply voltage (V) LEJ can be used. 200 to 230 VAC 
Control encoder: Absolute 20-bit encoder LEL Motor capacity (W) (Resolution: 10485

Lead 4: LEY32DC 50 Regenerative resistor area 60 Lead 8: LEY32DB 40 Work load [kg] Work load [kg] Lead 8: LEY32DB 30 40 Lead 16: LEY32DA 20 Lead 16: LEY32DA 20 10 0 0 0 200 400 600 800 1000 1200 0 200 400 600 800 1000 1200 Speed [mm/s] Speed [mm/s] Regenerative resistor area Applicable Motor/Driver * When using the actuator in the Regenerative resistor area, download the AC servo capacity

Environment

LEL 20 LEM 0 LEY LEY 0 200 400 600 800 1000 1400 1200 Speed [mm/s] LES LEY32 (Motor mounting position: Top/Parallel) LEY32D (Motor mounting position: In-line) LEPY LEPS 80 80 Lead 4: LEY32DC Lead 5: LEY32C LER Lead 8: LEY32DB 60 60 Lead 10: LEY32B Work load [kg] Work load [kg] Lead 16: LEY32DA LEH Area where the regeneration option is required.

15

SpeedVertical Work Load Graph LEY25l (Motor mounting position: Top/Parallel, In-line) 40 Lead 3: LEY25C 30 Work load [kg] 20 Lead 6: LEY25B 16 Lead 12: LEY25A 10 8 0 0 200 600 1000 1400 Speed [mm/s] LEY32l (Motor mounting position: Top/Parallel) LEY32D (Motor mounting position: In-line) 50 60 Lead 4: LEY32DC 50 Lead 5: LEY32C 40 46 37 40 Work load [kg] Work load [kg] 30 30 Lead 8: LEY32DB

Environment

LEL 20 LEM 0 LEY LEY 0 200 400 600 800 1000 1400 1200 Speed [mm/s] LES LEY32 (Motor mounting position: Top/Parallel) LEY32D (Motor mounting position: In-line) LEPY LEPS 80 80 Lead 4: LEY32DC Lead 5: LEY32C LER Lead 8: LEY32DB 60 60 Lead 10: LEY32B Work load [kg] Work load [kg] Lead 16: LEY32DA LEH Area where the regeneration option is required.

Size: 32, Motor Mounting Position: D (In-line Type), Motor: Step Motor (Servo 24 VDC), Lead Screw: C (Size 16: 2.5mm, Size 25: 3mm, Size 32/40: 4mm), Stroke: 300mm, Motor Option: None, Rod End Thread: M (Male)

Size: 32, Motor Mounting Position: In-line Type, Motor: Step Motor (Servo 24 VDC), Lead Screw: Size 16: 2.5mm, Size 25: 3mm, Size 32/40: 4mm, Stroke: 300mm, Motor Option: None, Rod End Thread: Male, Mounting: -, Actuator Cable: -, Actuator Cable Length: -, Controller Type - LEC, JXC: -, I/O Cable Length for LEC: -, Controller Mounting: -, Communication Plug Connector or I/O Cable Length for

Main Body Peripheral Component: Peripheral Components, Input Power Supply: DC 24V, Position Detection: Incremental, I/O Module: PNP, Motor Type: Step motor (24‑V DC servo), Step data (points): 64, Actuator/cable type: LEY32DC-100, I/O cable length / communication plug(m): Without I/O cable, Controller/driver mounting method: Screw mounting type

MY1

(between lead wire and case) Operating time .1.2ms Ambient temperature . 10 to 60C Impact resistance . 300m/s D-A90(V) Contact protection box OUT() Brown [Red] Reed switch CD-P11 OUT( ) Blue [Black] CD-P12 Leakage current . 0 Enclosure . IEC529 standard IP67 (JISC0920) watertight Note) Refer to page 12 for lead wire lengths.

MY1

(between lead wire and case) Operating time 1.2ms Ambient temperature 10 to 60C (14 to 140F) Impact resistance 300m/s Leakage current None Enclosure IEC529 standard IP67, watertight (JISC0920) For a lead wire length of 3m, "L" is shown at the end of the part number.

SMC Electronic Switch Series Variations

SMC Electronic Switch Series Variations Model Selection Table Self-contained Style ZSE1 ISE1 ZSE2 ISE2 PS1000 PS1100 ZSP1 GS40 ISA ZSE3 ISE3 Model General pneumatic Fluid Calibration method Trimmer calibration 0.1 to 0.45MPa 0.1 to 0.4MPa 0 to 0.98 MPa 101 to 20kPa 0.1 to 0.2MPa (Detection zone 10 to 300m) 0 to 100kPa 0 to 1MPa 101 to 0kPa 0 to 98kPa 0 to 0.98MPa 101 to 0kPa Calibration pressure

MY2

Do not drop, bump or apply excessive impacts (300m/s2 or more for reed switches and 1000m/s2 or more for solid state switches) while handling. Although the body of the switch may not be damaged, the inside of the switch could be damaged and cause a malfunction.

NCA1

When excessive impact (300m/s2 or more) is applied to a reed switch during operation, the contact point will malfunction and generate or cut off a signal momentarily (1ms or less). Consult SMC regarding the need to use a solid state switch depending upon the environment. 7. Do not use in an area where surges are generated.

REA/REB

When excessive impact (300m/s or more) is applied to a reed switch during operation, the contact point will malfunction and generate or cut off a signal momentarily (1ms or less). Consult SMC regarding the need to use a solid state switch depending upon the environment. 7. Do not use in an area where surges are generated.

Rotary Table

When excessive impact (300m/s2 or more) is applied to a reed auto switch during operation, the contacts may malfunction and generate or cut off a signal momentarily (1ms or less). Please consult with SMC if a solid state auto switch can be used according to the environment. Do not use in an area where surges are generated.

CE

Do not drop, bump or apply excessive impacts (300m/s or more for reed switches and 1000m/s or more for solid state switches) while handling. Although the body of the switch may not be damaged, the inside of the switch could be damaged and cause a malfunction. 2. Do not carry a cylinder by the auto switch lead wires.

Series CQ2

Heavy duty oil resistant vinyl cord, 3.4, 0.2mm, 2 wire (Brown, Blue [Red, Black]), 3 wire (Brown, Black, Blue [Red, White, Black]), 0.5m (D-Z73 only 2.7, 0.18mm, 2 wire) Impact resistance . 300m/S {30.6G} Insulation resistance . 50M or more at 500VDC (between lead wire and case) Withstand voltage .1500VAC for 1min.

CU

When excessive impact (300m/s or more) is applied to a reed switch during operation, the contact point may malfunction and generate or cut off a signal momentarily (1ms or less). Consult with SMC regarding the need to use a solid state switch depending on the environment. 7. Do not use in an area where surges are generated.

CXS

When excessive impact (300m/s or more) is applied to a reed switch during operation, the contact point may malfunction and generate or cut off a signal momentarily (1ms or less). Consult with SMC regarding the need to use a solid state switch depending on the environment. 7. Do not use in an area where surges are generated.

CY1

When excessive impact (300m/s2 or more) is applied to a reed switch during operation, the contact point will malfunction and generate or cut off a signal momentarily (1ms or less). Consult SMC regarding the need to use a solid state switch depending upon the environment. 7. Do not use in an area where surges are generated.