CATALOG ~60OC -20~60OC -20~60OC -20~60OC -20~60OC -20~60OC -20~60OC -20~60OC -20~60OC -20~60OC Material Polyurethane Polyurethane Polyurethane Polyurethane Polyurethane Polyurethane Polyurethane Polyurethane Polyurethane Polyurethane Courtesy of Steven Engineering, Inc. !
The following procedures are an example of how a test may be performed. It is intended as an overview and not as an all inclusive description. 1) Rotate the adjustment wheel counterclockwise (DECR) completely to relieve spring force.
AK VCHC 9. Do not apply excessive force or shock to the body or fittings with an impact tool. 6. Check if PTFE can be used in application. ASR ASQ PTFE powder (Polytetrafluoroethylene resin) is included in the seal material for piping taper thread of male thread type. Confirm that the use of it will not cause any adverse effect on the system.
T 2 x P (Rc, NPT, G) Q AH AG S U W K L B R A AL I J AI AJ AP 4 x AK hole AA AB V Y + Stroke X Z + Stroke For 4 x AO AG AN AI Cutout window AM Mounting dimensions (mm) Bore size (mm) 20 25 32 40 50 Stroke range (mm) AA AB AG AH AI AJ AK AL AM AN AO AP B I J K L M N O A 11 11 112 125 82 95 6.6 9 65 115 M6 25 108 30 55 60 80 25 45 M6 x 1 depth 9 90 75, 100, 125, 150, 200 14 13 134 150 92 108
with an are the same as standard.
22.4) 2 x 10-32 UNF depth 0.25 (6.3) (Mounting hole) 0 0.00 0 20 40 60 80 Flow rate (slpm, N2) AK1000HF 100 psig (0.69 MPa) 30 psig (0.21 MPa) Inlet pressure: 50 psig (0.34 MPa) 60 0.41 50 0.34 Delivery pressure (psig) Dlivery pressure (MPa) 40 0.28 30 0.21 20 0.14 10 0.07 0 0.00 0 20 40 60 80 100 120 140 160 180 200 Flow rate (slpm, N2) Hastelloy is a registered trademark of Haynes International
The following procedures are an example of how a test may be performed. It is intended as an overview and not as an all inclusive description. 1) Rotate the adjustment wheel counterclockwise (DECR) completely to relieve spring force.
Note 4) 2 locations on the back side for the standard-type 20 with 15 strokes or less and 25 with 10 strokes, and for models with an auto switch and built-in magnet of 20 with 5 strokes.
This product cannot be used to hold a stop position for an extended period of time. Pilot check valves and actuators are not guaranteed for zero air leakage. Therefore, it is sometimes not possible to hold a stop position for an extended period of time. In the event that holding for an extended time is necessary, a mechanical means for holding should be devised. 3.
2.5 to 6 6 to 20 20 to 40 40 to 63 63 to 100 AS13l1F AS13l1F AS23l1F AS33l1F AS43l1F / 1 8, / 1 4 / 1 4, / 3 8 / 1 2 Elbow (Metal Body) M5 6 to 20 20 to 32 20 to 40 40 to 63 63 to 100 AS12l1 AS22l1 AS22l1 AS32l1 AS42l1 / 1 8 4.1-7 / 1 4 / 3 8 / 1 2 In-line 6 to 20 20 to 32 20 to 40 40 to 63 63 to 100 AS1001F AS2001F AS2051F AS3001F AS4001F 4.1-9 Dual Speed Controller 6 to 20 20 to 32 20
Wiring Specs 20 20 Applicable up to 20 Solenoid M A N I F O L D O P T I O N S PORT PLUGS Applicable Fitting Size d A L D Model 16 32 6 KQP-04 4mm 16 32 6 KQP-03 5/32 18 35 8 KQP-06 6mm 18 35 8 KQP-07 1/4 20.5 39 10 KQP-08 8mm 20.5 39 10 KQP-09 5/16 Inserts easily into an unused cylinder port and/or SUP/EXH Ports.
2 AQ w t y q i o e ASV AK !0 VCHC ASR ASQ u @0 Meter-in type Meter-out type Component Parts No.
The following procedures are an example of how a test may be performed. It is intended as an overview and not as an all inclusive description. 1) Rotate the adjustment wheel counterclockwise (DECR) completely to relieve spring force.
The most typical is an increase in outlet pressure as the inlet pressure decays often stated as a given rise per a given drop in pressure. [Inboard leakage] Leakage rate from outside to inside of the products occurring when an internal pressure is less than the external pressure.
When the product is used for an actuator operating vertically, the actuator may lurch depending on the load. For the adjustment method, please refer to Selection and Adjustment on page 15-16-6 to 15-16-7. 4. For installation and removal, tighten the body B by applying an appropriate wrench to the two opposite sides of the hexagon. Using other parts may destroy the valve.
Applicable cylinder bore size (mm) Elbow type Universal type Port size Metric size Inch size 12 10 8 6 4 3.2 1/8" 5/32" 3/16" 1/4" 5/16" 3/8" 1/2" AS131FG-M5 AS121FG-M5 M50.8 6, 10, 16, 20 AS231FG-01 AS221FG-01 20, 25, 32 R 1/8 AS231FG-02 AS221FG-02 20, 25, 32, 40 R 1/4 AS331FG-02 AS321FG-02 40, 50, 63 R 1/4 AS331FG-03 AS321FG-03 40, 50, 63 R 3/8 AS431FG-04 AS421FG-04 63, 80, 100 R 1/2
With one-touch fitting For low speed control AS Needle Valve/Flow Characteristics ASP AS1001FM AS2001FM AS2051FM ASN 0.8 Inlet pressure: 0.5 MPa Inlet pressure: 0.5 MPa Inlet pressure: 0.5 MPa 10 20 50 0.15 0.3 AQ Flow rate (l/min (ANR)) Flow rate (l/min (ANR)) Flow rate (l/min (ANR)) Effective area (mm2) Effective area (mm2) Effective area (mm2) 40 0.6 ASV 0.1 0.2 30 AK 5 10 0.4 20 0.05
2 AQ q w ASV y t AK i VCHC o ASR ASQ !0 u !5 e Meter-out type Meter-in type Component Parts No.
2 AQ w t y q i o e ASV AK !0 VCHC ASR ASQ u @0 Meter-out type Meter-in type Component Parts No.
Application Example for Check Valve with One-touch Fitting Prevention of reverse flow to vacuum source (Simple vacuum holding) Tank pressure reverse flow prevention AS ASP ASN AQ ASV AK ASS Drop prevention ASR ASF A certain amount of leakage is allowed in the specifications of this product. Please note that it is not suitable for holding over an extended period of time.