Cooling Capacity: 38 kW, Cooling Method: Air-cooled Refrigeration, Pipe Thread: NPT, with Rc-NPT Conversion Fitting, Power Supply: 50/60Hz: 3-phase 380 to 415 VAC; 60Hz: 3-phase 460 to 480 VAC, Option: -
High Vacuum Angle Valve An auto switch magnet is not installed. In cases where an auto switch magnet is installed, add -M9// to the part number. (Not available for the high-temperature type) An auto switch is not attached. When a product with an auto switch is required, add the symbol for the auto switch to the part number.
the connections from Rc to NPT is enclosed as an accessory.
[Tips]
Connect the remote control cable and the switch to the connector for the contact input/output, supplied as an accessory. Then, mount the ferrite core (3 turn) supplied as an accessory. (See below) (This is an example of wiring. Refer to the Operation Manual for communication for details.)
Install an air dryer, aftercooler, etc. Excessive condensate in a compressed air system may cause valves and other pneumatic equipment to malfunction. Installation of an air dryer, after cooler etc. is recommended. 3. Drain flushing If condensate in the drain bowl is not emptied on a regular basis, the bowl will over flow and allow the condensate to enter the compressed air lines.
Connect the remote control cable and the switch to the connector for the contact input/output, supplied as an accessory. Then, mount the ferrite core (3 turn) supplied as an accessory. (See below) (This is an example of wiring. Refer to the Operation Manual for communication for details.)
This information is needed when contacting an SMC sales distributor. (It is an example of model "HRS040-A-20".)
Connect the remote control cable and the switch to the connector for the contact input/output, supplied as an accessory. Then, mount the ferrite core (3 turn) supplied as an accessory. (See below) (This is an example of wiring. Refer to the Operation Manual for communication for details.)
Connect the remote control cable and the switch to the connector for the contact input/output, supplied as an accessory. Then, mount the ferrite core (3 turn) supplied as an accessory. (See below) (This is an example of wiring. Refer to the Operation Manual for communication for details.)
Vacuum switch Series ZS 13-1-6 Model Selection Single Unit System Equipment such as an ejector is configured as an individual unit. Thus, it is possible to create a flexible system configuration in which the circuit composition and the mounting locations can be selected as desired.
If the compressed air supply includes chemicals, synthetic materials (including organic solvents), salinity, corrosive gas, etc., it can lead to damage or malfunction. 2) Install an air filter. Install an air filter at the up stream side to the valve. Filtration degree should be 5 m or less. 3) Install an air dryer, after cooler, etc.
Do not use the cylinder under the following environments: An area in which fluids such as cutting oil splash on the piston rod An area in which foreign matter such as particles, cutting chips, or dust is present An area in which the ambient temperature exceeds the operating range An area exposed to direct sunlight An environment that poses the risk of corrosion 2.
Connect the remote control cable and the switch to the connector for the contact input/output, supplied as an accessory. Then, mount the ferrite core (3 turn) supplied as an accessory. (See below) (This is an example of wiring. Refer to the Operation Manual for communication for details.)
Connect the remote control cable and the switch to the connector for the contact input/output, supplied as an accessory. Then, mount the ferrite core (3 turn) supplied as an accessory. (See below) (This is an example of wiring. Refer to the Operation Manual for communication for details.)
, making it possible to hold a cylinder intermediate stopping position for an extended time.
This product cannot be used to hold a stop position for an extended period of time. Pilot check valves and actuators are not guaranteed for zero air leakage. Therefore, it is sometimes not possible to hold a stop position for an extended period of time. In the event that holding for an extended time is necessary, a mechanical means for holding should be devised. 3.
This product cannot be used to hold a stop position for an extended period of time. Pilot check valves and actuators are not guaranteed for zero air leakage. Therefore, it is sometimes not possible to hold a stop position for an extended period of time. In the event that holding for an extended time is necessary, a mechanical means for holding should be devised. 3.
When the product is used for an actuator operating vertically, the actuator may lurch depending on the load. For the adjustment method, please refer to Selection and Adjustment on page 15-16-6 to 15-16-7. 4. For installation and removal, tighten the body B by applying an appropriate wrench to the two opposite sides of the hexagon. Using other parts may destroy the valve.
Features Power Consumption Comparison Energy saving Type Conventional type An energy saving type thermo-chiller is added to the conventional series INR-499.