Made to Order CM2 series A port B port C port Stroke (mm) SA SB ZZ Bore size 20 48 62 164 SB + Stroke SA + Stroke 25 48 62 168 ZZ + 2 x Stroke 32 50 64 172 D port 40 67.5 88.5 222 1794 Made to Order Common Specifications: Tandem Cylinder Symbol -XC12 Dimensions (Dimensions other than below are the same as standard type.)
V v v CG1l-lJ K v CG1lH CG1 CG1 V v v v 10-, 11CG3 v v v v v v v 25ANote 9) JMB V V v v v 20Note 9) v v v v CG1lR V v v CG1lM MB MB1 v v XB6 Note 2) Note 2) Note 15) v XB7 CA2 v v v XB9 Note 15) v XB13 Note 15) CS1 v v v v XC4 CS2 v v XC6 v v v v v XC8 Note 15) Note 13) Note 13) v v v v v XC9 Note 15) Note 14) Note 14) v v v v v v v XC10 v v v v v v v XC11 v v v v v XC12
Dual stroke/Double rod -XC10 10 Tandem type -XC12 12 Two cylinders are combined in a back-to-back configuration, allowing the two reciprocating cylinder strokes to be controlled in three steps. Two cylinders are connected in-line, allowing cylinder output to be doubled. Standard part no.
MB XC12 Tandem cylinder Specifications Action Min. operating pressure Cushion Mounting Double acting, Single rod 0.1MPa Air cushion B, L, F, G, C, D type (T not available) The specifications other than the above are the same as those of the standard type.
(Or None in the Case of No Switch), Stroke Options: XC12 (Tandem Cylinder)
Magnet: None, Mounting: Basic, Double-side Bossed, Bore Size: 40mm, Port Thread: Rc, Stroke A: 75mm, Rod End Thread A: Male Rod End, Rod Boot A: None, +: None, Stroke B: None, Cushion: Rubber Bumper, Rod End Thread B: Male Rod End, Rod Boot B: None, Pivot Bracket: None, Rod End Bracket: None, Auto Switch: No Switch, Lead Wire or Prewired Connector: 0.5m (Or None in the Case of No Switch),
XC69 Fluororubber seal Shaft and parallel key made of stainless steel X6 Among the symbols XC8 to XC21, only XC12 and XC16 are compatible with shaft types X, Z, T, J and K. DCaution (1) The angle adjusting screw (angle adjustment bolt) is set at random within the adjustable rotating range. Therefore, it must be readjusted to obtain the angle that suits your application. 247
X6 T,J,K Among the symbols XC8 to XC21, only XC12 and XC16 are compatible with shaft types X, Z, T, J and K. DMoisture Control Tube IDK Series When operating an actuator with a small diameter and a short stroke at a high frequency, the dew condensation (water droplet) may occur inside the piping depending on the conditions.
Clean Series 40 to 63 Copper and Fluorine-free Water resistant (NBR seal) 40 to 100 Water resistant (FKM seal) Change of rod end shape Oversized rod cylinder Heat-resistant cylinder (10 to 150 C) Special port position With heavy duty scraper Heat-resistant cylinder (10 to 110 C) Made of stainless steel Tie-rod, cushion valve, XC7 tie-rod nut, etc. made of stainless steel XC8 XC9 XC10 XC11 XC12
-XC11 Dual stroke cylinder/Single rod type -XC12 Tandem type cylinder -XC13 Auto switch rail mounting style -XC18 NPT finish piping port Rod Boot Material -XC20 Head cover axial port Maximum operating temperature -XC22 Fluoro rubber seals Symbol Rod boot material -XC29 Double knuckle joint with spring pin Nylon tarpaulin J 70C -XC35 With coil scraper 110C Heat resistant tarpaulin K -XC37
and rod end nut made of stainless steel 25 301 to 400 10 mm 15 mm -XC8 Adjustable stroke cylinder/Adjustable extension type 32 301 to 450 20-XC9 Adjustable stroke cylinder/Adjustable retraction type 25, 50, 75, 100, 125, 150, 200, 250, 300 40 15 mm 20 mm 1500 301 to 800 D-B59W -XC10 Dual stroke cylinder/Double rod type Data 50, 63 301 to 1200 -XC11 Dual stroke cylinder/Single rod type -XC12
Select the desired range (“-XC12” to “-XC15”) and add the corresponding suffix to the end of the CDRQ2BSP40-90 part number. Check the catalog for details on the “-XC12” to “-XC15” suffixes as the position of the start and end points vary.
The CRQ2 series catalog can be found here.
dual stroke with 3 position (single rod type) ; XC12 is tandem dual force cylinder ; Bore sizes (mm): 20, 25, 32, 40 ; Variety of switches and lead wire lengths
dual stroke with 3 position (single rod type) ; XC12 is tandem dual force cylinder ; Bore sizes (mm): 20, 25, 32, 40 ; Variety of switches and lead wire lengths
with 3 position (single rod type); XC12 is tandem dual force cylinder; Bore sizes (mm): 20, 25, 32, 40; Variety of switches and lead wire lengths
Magnet: None, Type: Pneumatic, Mounting: B (Basic), Bore: 40mm, Port Thread: Rc, Stroke: 50mm, Cushion: Rubber Bumper, Rod End Thread: Male Rod End, Rod Boot: None
Cylinder (Tube) Inner Diameter(φ): 40, Stroke(mm): 50, Cylinder Operation Method: [Double Acting] Double Acting, Rod Operation Method: Single Rods, Main Body Shape: Standard, Additional Function: Standard, Environment, Applications: Standard, Operating Temperature(°C): -10～70, Operating Pressure(MPa): 0.05～1, Cushion: Rubber cushion, Specification: Without built-in magnet, Port thread type
Cylinder (Tube) Inner Diameter(φ): 40, Stroke(mm): 50, Cylinder Operation Method: [Double Acting] Double Acting, Rod Operation Method: Single Rods, Main Body Shape: Standard, Additional Function: Standard, Environment, Applications: Standard, Operating Temperature(°C): -10～70, Operating Pressure(MPa): 0.05～1, Cushion: Rubber cushion, Specification: Without built-in magnet, Port thread type
CA2-40Z-PS CA2-50Z-PS CA2-63Z-PS CA2-80Z-PS CA2-100Z-PS Rod seal 1 pc Contents Piston seal 1 pc of the Cushion seal 2 pc seal kit Cylinder tube gasket 2 pc Note) Seal kits include grease pack.
MB32ZCA2-40Z CA2-50Z CA2-63Z CA2-80Z CA2-100 Z-PS MB125-PS PS -PS -PS -PS -PS Rod seal 1 pc Contents of Piston seal 1 pc the seal kit Cushion seal 2 pc Cylinder tube gasket 2 pc Note) Seal kits include grease pack.