Controller/Driver LEC/JXC Series <Single Axis Controllers> Step Data Input Type Page 560 Gateway Unit Page 572 Programless Type Page 576 Step Motor LEC-G Series Step Motor Servo Motor (Servo/24 VDC)/ (Servo/24 VDC)/ (24 VDC)/ LECP6 Series LE If the current pushing force exceeds the Trigger LV value of the step data, INP signal will turn ON. Note) If pushing operation is stopped when there is no pulse deviation, the moving part of the actuator may pulsate.
Trigger LV is the setting to define the conditions where INP will turn ON. When the actuator generates a force greater than this value, INP will turn ON. This parameter is set according to the value of the pushing force or lower. (Unit: %) For the positioning operation, this value is ignored. Trigger LV Trigger LV (1) -39No.
When [Pushing force] setting and [Trigger LV] are set less than [Pushing force], use the product within the specified range of [Pushing force] and [Trigger LV]. a) To ensure that the actuator pushes the workpiece with the set [Pushing force], it is recommended that the [Trigger LV] be set to the same value as the [Pushing force]. b) If the [Trigger LV] is set lower than the [operation pushing
Use the product within the specified range of [Pushing force] and [Trigger LV]. a) To ensure that the gripper holds the workpiece with the set [Pushing force], it is recommended that the [Trigger LV] be set to the same value as the [Pushing force]. b) When the [Pushing force] and [Trigger LV] are set less than the specified range, the INP output signal will turn on from the pushing start
New Products Guide 1 Directional Control Valves Actuators Vacuum Equipment CAT.E00-6A INDEX New Products Guide 1 Directional Control Valves 5 Port Solenoid Valve Fieldbus System (For Input/Output) 2/3 Port Mechanical Valve Series SY3000/5000/7000 Series EX600 Series VM100/200 P .6 P .264 P .322 Actuators Foot Pedal Type 5 Port Mechanical Valve XT34-60/67 Air Cylinder Air Cylinder Series CJ2
When [pushing force] setting and [trigger LV] are set below [pushing force], use the product within the specified range of [pushing force and trigger LV]. a) To ensure that the product pushes the workpiece with the set [pushing force], it is recommended that the [Trigger LV] is set to the same value as the [pushing force]. b) If the [trigger LV] is set lower than the [operation pushing force
Retaining rings (cotter pins for 40) are attached. 620-1 Series CLM2 Clevis Pivot Bracket (For CLM2E) (mm) Rod End Nut (mm) Material: Carbon steel Material: Rolled steel plate d L LV LX D C LC hole + 0.15 + 0.05 Axis 0.040 0.076 LR H B Applicable bore size 20 25, 32 40 D d H B C Part no.
Initial value: Set to [0.50] or higher. 2) Pushing operation When the effective force exceeds step data [Trigger LV], the INP output signal will turn on. Use the product within the specified range of [Pushing force] and [Trigger LV].
The [Trigger LV] should be set between 40% and [Pushing force]. a) To ensure that the clamping and external stop is achieved by [Pushing force], it is recommended that the [Trigger LV] be set to the same value as the [Pushing force]. b) When the [Pushing force] and [Trigger LV] are set less than the specified range, the INP output signal will turn on from the pushing start position. 1.
Driving speed when pushing operating should be set within specification range. 2) Pushing operation When the effective force exceeds step data [Trigger LV], the INP output signal will be turned on. Set the [Pushing force] and [Trigger LV] within the limitation range. It may damage and malfunction. 4.
When operated at a very low flow rate, the series LV with flow rate adjustment may vibrate, etc. depending on the operating conditions. Therefore, operate it after careful examination of the flow rate, pressure and piping conditions. 3. In the series LV, water hammering may occur depending on the fluid pressure conditions.
parameters Max force Trigger LV
Trigger LV Setting is not required. Pushing speed Condition that turns on the INP output signal. The INP output signal turns on when the generated force exceeds the value. Trigger level should be the pushing force or less. Max. torque during the positioning operation (No specific change is required.) Moving force D = D Trigger LV Condition that turns on the AREA output signal.
Trigger LV Setting is not required. Pushing speed Condition that turns on the INP output signal. The INP output signal is turned on when the generated force exceeds the value. Threshold level should be less than the pushing force. Max. torque during the positioning operation (No specific change is required.) Positioning force Trigger LV Condition that turns on the AREA output signal.
If the pushing force is kept higher than the value specified by "Trigger LV" of the step data for a certain time again, the INP output will be reactivated.
If the pushing force is kept higher than the value specified by "Trigger LV" of the step data for a certain time again, the INP output will be reactivated.
LV at the time of Pushing force = 0, the alarm will not be activated.) (3) Minimum speed of actuator Pushing speed Speed (4) Pushing speed Maximum pushing speed of actuator (5) Pushing force Minimum pushing force of actuator (6) Basic parameters Max force Minimum pushing force of actuator (7) Basic parameters Max force Trigger LV Step data ALM1 (1-048) B RESET input
When [Pushing force] setting and [Trigger LV] are set less than [Pushing force], use the product within the specified range of [Pushing force] and [Trigger LV]. a) To ensure that the actuator pushes the workpiece with the set [Pushing force], it is recommended that the [Trigger LV] be set to the same value as the [Pushing force]. b) If the [Trigger LV] is set lower than the [operation pushing
Voltage VDW AC DC Thread type 5 6 9 24VDC 12VDC 1 2 3 4 9 100VAC 200VAC 110VAC 220VAC VC Rc G NPT NPTF Nil F N T (Other, less than 50VDC) LV (Other, less than 250VAC) PA AC specifications are only for DIN terminal and conduit terminal type. Port size Consult SMC regarding other voltages (9).
Selection of Pushing Speed P Set the [Pushing force] and the [Trigger LV] within the range shown in the figure below.