PSE550/300 Do not drop, bump, or apply excessive impact (100 m/s2) while handling. Although the body of the controller case may not be damaged, the inside of the controller could be damaged and cause malfunction. 2. The tensile strength of the power supply/output connection cable is 50 N; that of the pressure sensor lead wire with connector is 25 N.
Do not drop, or apply excessive impact (980 m/s2) while handing. Although the body of the sensor may not be damaged, the internal parts of the sensor could be damaged and lead to a malfunction. 2. The tensile strength of the cord is 49 N. Applying a greater pulling force on it can cause a malfunction. When handling, hold the body of the sensor do not dangle it from the cord. 3.
Note 4) (ft/s2) 30/150 (9/150ft/s2) Rated voltage 24VDC, 12VDC, 100VAC, 110VAC, 200VAC, 220VAC (50/60Hz) Allowable voltage fluctuation % 10% of rated voltage Coil insulation type Class B Enclosure Note 5) Dust proof (equivalent to IP40) Power consumption W Note 3) 2.5 (VDW10), 3 (VDW20/30) Note 1) Consult SMC when used under conditions which may cause condensation on the exterior of the
Note 4) Kit/Electrical entry/Cable length F P kit (D-sub connector) kit (Flat ribbon cable connector) Note 1) 26P 26P Note 1) Note 1) 25P Side entry Top entry Side entry Top entry Note 1) 25P Connector entry direction Top entry Side entry Connector entry direction Top entry Side entry U0 U1 U2 U3 P. 2-4-76 P. 2-4-78 U0 U1 U2 U3 S0 S1 S2 S3 S0 S1 S2 S3 Without cable With cable (1.5 m) With
The table will move to the target position according to a trapezoidal movement profile shown in the diagram on the right based on the set speed Vc [mm/s], acceleration Aa [mm/s2] and deceleration Ad [mm/s2].
3280 ft/s2 Insulation resistance 50 M or more at 500 VDC (between lead wire and case) 1500 VAC for 1 min.
Refer to page 4-18-4.) 15 or less Max. operating frequency (Hz) 10 Non-locking push type, push-turn locking slotted type, push-turn locking lever type Manual override (Manual operation) Individual exhaust for the pilot valve, common exhaust for the pilot and main valve Pilot exhaust method Body ported Lubrication Mounting orientation Shock/Vibration resistance (m/s2) Note 2) Not required
Auto Switches Common Specifications Type Reed auto switch Solid state auto switch 1 ms or less 1.2 ms Operating time 300 m/s2 1000 m/s2 Impact resistance 50 M or more at 500 VDC Mega (Between lead wire and case) Insulation resistance 1500 VAC for 1 minute (Between lead wire and case) 1000 VAC for 1 minute (Between lead wire and case) Withstand voltage 10 to 60C Ambient temperature IEC60529
in X, Y, Z directions for 2 hrs. each (De-energized) 100 m/s2 in X, Y, Z directions 3 times each (De-energized) 2% F.S.
Do not drop, bump or apply excessive impacts (300 m/s2 or more for reed switches and 1000 m/s2 or more for solid state switches) while handling. Although the body of the auto switch may not be damaged, the inside of the auto switch could be damaged and cause a malfunction. 2. Mount auto switches using the proper tightening torque.
Conversion example for a 8[mm] lead actuator driven at an acceleration of 3000 [mm/sec2] Acceleration/Deceleration time constant (ms) = {3000 (r/min) 60 (S) } 8 (mm) 1000 3000 (mm/s2) Rated Motor Rotation Speed (mm/s) Acceleration time constant/deceleration time constant (ms) = {Rated rotation speed (r/min) 60 (S) } x screw lead (mm) x 1000 Acceleration/deceleration speed (mm/s2) *Note)
Conversion example for a 8[mm] lead actuator driven at an acceleration of 3000 [mm/sec2] Acceleration/Deceleration time constant (ms) = {3000 (r/min) 60 (S) } 8 (mm) 1000 3000 (mm/s2) Rated Motor Rotation Speed (mm/s) Acceleration time constant/deceleration time constant (ms) = {Rated rotation speed (r/min) 60 (S) } x screw lead (mm) x 1000 Acceleration/deceleration speed (mm/s2) *Note)
STO 13.3.3 3.2.2 ISO/EN ISO 13849-1 3 PL d 24 V EMG S4 S3 KM1 S2 KM1 K3 +24 V XS0 XS1 Z00 Z10 Z20 KM1 MELSEC (QS90SR2S) KM1 X0 COM0 24G X1 COM1 Z01 Z11 Z21 CN8 STO1 S1 EMG () STO2 STOCO M K3 TOFB1 TOFCOM 0 V TOFB2 20 S1STO (STO ) S2(STO ) S3ON S4OFF KM1 K3 EMG CN3 EM1 EM2 M . STOS1EMG0 STO[AL. 63 STO] 13.
The station address is set using the rotary switches S1 and S2. (1) Settings of the Rotary Switches S1 and S2 Set the station address using the rotary switches S1 and S2.
Note 4) (ft/s2) 30/150 (9/150ft/s2) Rated voltage 24VDC, 12VDC, 100VAC, 110VAC, 200VAC, 220VAC (50/60Hz) Allowable voltage fluctuation % 10% of rated voltage Coil insulation type Class B Enclosure Note 5) Dust proof (equivalent to IP40) Power consumption W Note 3) 2.5 (VDW10), 3 (VDW20/30) Note 1) Consult P/A when used under conditions which may cause condensation on the exterior of the
Do not drop, bump or apply excessive impacts (300 m/s2 or more for reed auto switches and 1000 m/s2 or more for solid state auto switches) while handling. Although the body of the auto switch may not be damaged, the inside of the auto switch could be damaged and cause malfunction. 2. Observe the proper tightening torque for mounting an auto switch.
amplitude in X, Y, Z directions for 2 hours each (De-energized) Vibration resistance 980 m/s2 in X, Y, Z directions 3 times each (De-energized) Impact resistance Temperature characteristics (Based on 25C: within operating temperature range) 2%F.S. or less Standards CE Marking, UL/CSA (UL508) compliance Fitting: C3604 (electroless nickel plated), Sensor port: PBT, Sensor pressure receiving
Move mm/s2 mm/s2 mm/s mm mm/s mm mm mm 0 Absolute 100 20.00 1000 1000 0 0 0 100 18.00 22.50 0.5 1 Absolute 50 10.00 1000 1000 70 60 5 100 6.0 12.0 1.5 63 Absolute 20 5.00 500 500 0 0 0 100 3.0 8.0 1.2 28 - Details of step data Setting name Range Description No. 0 to 63 Number of the step data. The setting to specify the coordinate system for the target position.
.: 1.4 mm Vibration resistance1 30 m/s2 Without pressure sensor/switch With pressure sensor 20 m/s2 With pressure switch Impact2, 3 resistance 150 m/s2 Without pressure sensor/switch With pressure sensor 100 m/s2 With pressure switch Standards CE marking, RoHS 4 Refer to the Valve assembly on page 32 for the valve model number. 5 ZK2-VAmR: After instantaneous energization of the supply valve
3280 ft/s2 Insulation resistance 50 M or more at 500 VDC (between lead wire and case) 1000 VAC for 1 min.