Fieldbus system PROFINET compatible SI Unit with IEC60068-2-6) Vibration resistance Impact resistance 147 m/s2 is given 3 times for each direction X, Y and Z (complies with IEC60068-2-27) Operating environment No corrosive gas 13 No.EX-OMW0011-B 3.
) Note6) Vertical Basic 0.5 0.25 1.5 1.0 Compact 1.5 1.0 Basic 10 to 150 20 to 300 Note4) 10 to 200 20 to 350 Note4) Actuator specification Horizontal Compact 10 to 200 20 to 350 Note4) Speed [mm/s] Note3) Note6) Vertical Basic 10 to 150 20 to 300 Note4) 10 to 150 20 to 300 Note4) Compact 10 to 150 20 to 300 Note4) Pushing speed [mm/s] Note5) 10 20 10 20 Acceleration / Deceleration [mm/ s2
Indicator light Electrical entry Lead wire Grommet Oilproof flexible heavy-duty vinyl cord, 2.7 x 3.2, ellipse Switch, 1,000 m/s2 Impact resistance Connector, 300 m/s2 JIS C 4524, JIS C 4525 IEC 947-5-2, NECA 0402 In compliance with IP 67 when coupled 50 M or more (500 VDC Mega) between lead wire and case 1,000 VAC for 1 min.
The unit conversion between SI and conventional units are as follows: Oscillation acceleration 100m/s2 = 10.1972G Pressure 1MPa = 10.1972kgf/cm2 Cylinder thrust/load 100N = 10.1972kgf Standard air: Symbol (ANR) Torque 1Nm = 10.1972kgfcm Temperature 20C {293K}, Air with Moment of inertia 1kgm2 = 10.1972kgcm/s2 an absolute pressure of 760 mmHg Kinetic energy 1J = 10.1972kgcm {101.3kPa}, and
With the 0.1 W specification, the vibration and impact resistance is 10/50 m/s2 or less. Note 3) With the low vacuum specification, the operating pressure range is 1.33 102 Pa to the maximum operating pressure.
With the 0.1 W specification, the vibration and impact resistance is 10/50 m/s2 or less. Note 3) With the low vacuum specification, the operating pressure range is 1.33 102 Pa to the maximum operating pressure.
P1 LED lever meter Sensor S1 S3 Red is on: Output OFF Green is on: Output ON S4 S2 + P2 Red 1 Gap too big S1, S2: Fixed orifice S3: Variable orifice (Set via adjustment knob) S4: Detection nozzle Red 2 Green 1 BEST POSITION The bridge circuit is constructed as shown in the diagram. Position the work piece in front of the nozzle (S4).
Do not drop or apply the excessive force (1000 m/s2) to a switch when handling. Do not drop, or bump, or apply the excessive force (more than 1000 m/s2) when handling a switch. The internal parts of a switch are damaged, and may result in a malfunction, even though a switch case itself is not damaged. 2. When handling a switch, hold it by the switch body.
With the 0.1 W specification, the vibration and impact resistance is 10/50 m/s2 or less. Note 3) With the low vacuum specification, the operating pressure range is 1.33 102 Pa to the maximum operating pressure.
Mount the switch in a locations where there is no vibration greater than 98 m/s2 or impact greater than 490 m/s2. 3. Do not use in an area where surges are generated.
REC Smooth acceleration & deceleration at 5 CX CY MQQ M Acceleration Stroke Cushion seal RHC MK(2) 15 m/s2 5 m/s2 (REB) (REA) RS Q G High precision guide type: REAHT (Double axis) High precision guide type: REBHT (Double axis) RS H A REB REA RZQ High precision guide type: REAH (Single axis) High precision guide type: REBH (Single axis) MI W S High Linear guide (Double axis) installed in the
Do not drop, bump or apply excessive impacts (980 m/s2 or more for sensor unit and 98 m/s2 or more for amplifier unit) while handling. Although the trimmer auto switch body may not be damaged, the inside of the trimmer auto switch could be damaged and cause a malfunction. 2. Refer to the Operation Manual for how to adjust/set. Maintenance Warning 1.
(Value in the initial stage) Note 3) Vibration resistance is 50 m/s2 when a light/surge voltage suppressor is attached. Note 4) No inrush voltages are generated in the AC solenoid because a full-wave rectifier is used. VXA VCH VDW Construction VQ Component Parts !6 e !5 o y i q t u !0 !1 e w r !3 !8 !7 @3 @0 !9 @4 @1 @2 @6 @5 @7 @8 LVM No.
After improvement Before improvement Conventional coil tube model Filter regulator Conventional coupler model S coupler 1 2 1 2 Coil tube L L VMG Air gun Nozzle 2.5 Nozzle 3 S2 S0 to S1 S2 S0 to S1 Effective area ratio 3.04 : 1 Effective area ratio 0.69 : 1 Before improvement After improvement Coupler S coupler Conventional model Piping Equipment TCU1065-1-20-X6 Conventional coil tube model
Note) Old VXZ bracket mounting hole center position 26 Zero Differential Pressure Type Pilot Operated 2 Port Solenoid Valve Series VXZ Air Air Oil Water Dimensions/Body Material: Aluminum, C37, Stainless Steel For Air Specifications For Water For Oil Options Construction Dimensions For Heated Water For High Temperature Oil Conduit Conduit terminal 34 D D G1/2 Q2 S2 F F Q 280 23 32 a e E R
m/s2) *3 100 *1: Values are based on standard of SMC measurements.
Smooth acceleration & deceleration at 5 Acceleration Stroke 15m/s2 (REB) 5m/s2 (REA) REB REA 1/2 T T Time Cushion ring The exterior of the cushion ring is provided with a variable throttle groove in its longitudinal direction.
(Between lead wire and the case) 1000 m/s2 300 m/s2 Impact resistance 50 M or more at 500 M VDC (Between lead wire and case) Insulation resistance 1500 VAC for 1 minute 1) (Between lead wire and case) 1000 VAC for 1 minute (Between lead wire and case) Withstand voltage Except magnetic resistant 2-color indication type solid state switch (DP5DWL/P5DWSC).
ripple 10% or less) Current consumption 20mA or less (without load) Enclosure IP65 Operating temperature range Operating: 0 to 50C, Stored: 25 to 85C in stock (no freeze nor condensation) Environmental resistance Voltage resistance 1000VAC for 1 min between external terminals and case Insulation resistance 50M or more (500VDC) between external terminals and case Vibration resistance 4.9m/s2