Vacuum Equipment Average suction flow rate Ball joint type 1 2 1 3 A pad with a low electrical resistance that is used as an electrostatic prevention measure. Any pressure below the atmospheric pressure.
113 132 20 222 250 279 25 282 319 355 32 445 494 542 639 40 517 570 623 728 50 921 1001 1081 1241 63 1256 1364 1472 1687 Use a clamp arm that is available as an option.
Installation on a mounting surface with a rough surface, scratches or dents, or mounting an unsuitable O-ring may cause sealing failure.
10 to 60 99 79 6.6 8 42 52 20 FX FT 10 to 50, 75, 100 106.5 84.5 5.5 8 48 56 25 B + Stroke L FZ 10 to 50, 75, 100 126 104 5.5 8 54 62 28 2-FD A + Stroke 25, 28 Bore size (mm) FZ L M 55 18 10 60 20 16 FV 64 20 20 65 22 34 25 72 22 FT 40 28 FX B + Stroke L FZ A + Stroke 4-FD Rear flange type/MQQLG 10, 16, 20 (mm) 25, 28 Bore size (mm) Stroke range (mm) A L 4-FD 2-FD 75 8 10 10 to 40 88.5
A 17.5 26 23 16 A 26 27.5 28 25 28.5 B 18 16.5 21 31.5 37.5 B 15.5 11 14.5 21.5 Bore size (mm) 16 20 25 32 Bore size (mm) 40 50 63 80 100 CXW CXS CXT MX How to Mount and Move an Auto Switch MXU Refer to p.5.3-73 for details.
, during an intermediate stop with a 3 position closed center or perfect type valve.
) If requiring a built-in magnet cylinder without an auto switch, refer to the model number example below.
: One-touch fitting 1(P): Male thread 2(A): One-touch fitting 1(P): One-touch fitting 2(A): Male thread 1(P): Male thread 2(A): Male thread 2(A) 2(A) 2(A) 2(A) Applicable tubing O.D.
When the dryer is drawing in high temperature air that is discharged from an air compressor or other dryer. The ventilation port is obstructed by a wall or clogged with dust. Cleaning of Ventilation Area Caution Remove dust from the ventilation area once a month using a vacuum cleaner or an air blow nozzle.
For a facility having a small installation area (that can not vent the air naturally): Make a forced air exhaust vent on a wall at a high level and an air inlet on a wall at a low level. 3.
K E O F F TA K EO F F T Y P E 1 "T" Type 4 "X" Type T H R E A D T Y P E Nil Rc(PT) N NPT P O R T S I Z E M5 M5 x 0.8 01 1/8 02 1/4 03 3/8 04 1/2 mm mm Model Port Size A B C Model Port Size A B C D Y11-M5 M5X0.8 8 12 8 Y14-M5 M5 23 16 14 25 Y21-01 1/8 10 29 19 Y24-01 1/8 40 40 22 40 Y21-02 1/4 10 29 19 Y24-02 1/4 40 40 22 40 Y31-01 1/8 11 33 19 Y34-02 1/8 49 43 28 48 Y31-02 1/4 11 33 19 Y44
Maintain a minimum cylinder separation of 40 mm. 3. Pay attention to the length of time that a switch is on at an intermediate stroke position. When an auto switch is placed at an intermediate position of the stroke and a load connected to the auto switch is driven at the time the slide table passes, the auto switch will operate.
(At 15 m: Reduced by up to 20%) Note 7) A reference value for correcting an error in reciprocal operation. Note 8) Impact resistance: No malfunction occurred when the actuator was tested with a drop tester in both an axial direction and a perpendicular direction to the lead screw. (Test was performed with the actuator in the initial state.)
An angle of deviation that exceeds 3 will place an excessive load on the bearings, leading to oil leaks within a short period of operation. Danger 1. Operation in an environment which requires explosion-proof When mounting in places where static electricity is accumulated, implement a distribution of electrical energy by grounding.
Outside Inside the controller 10k (a) 1k (a) IN0
Multistage Ejector RoHS Only for the models with a valve or pressure switch The ZL1 with an AC voltage valve is not compliant.
In such a case, it will be necessary to use ZSP1 that can detect a small hysteresis or a flow switch. Note) A vacuum generator with a large suction capacity will not be detected properly, so an ejector with an appropriate capacity must be selected. Since the hysteresis is small, vacuum pressure must be stabilized.
(Including insulating material) 1.5 mm 1.27 mm 1.65 mm 1.27 mm Rated current 3 A 4 A 3.1 A 4 A Rated voltage 125 V 60 V 125 V 60 V Contact resistance 40 mW or less 5 mW or less 40 mW or less 5 mW or less Insulation resistance 1000 MW or more 100 MW or more 1000 MW or more 100 MW or more Withstand voltage 1.5 kV 1.0 kV 1.5 kV 1.0 kV Rating/Performance Ambient temperature Connector 25 to +60C
B C A B C A B C A Black For supply valve (,+) + + + ZK2-ZSmBmm-A (PNP 2 outputs) + Pilot valve for supply + B C A LED (Red) White White White White Pilot valve for supply + Pilot valve for release Pilot valve for release + Pilot valve for release Pilot valve for release + B C A + + White White Connector cord assembly (ZK2-LWA20-A) Connector cord assembly (ZK2-LWB20-A) Brown DC(
OFF 45 ON Max. 6 38 24.5 Symbol 3 port (A) 2 (A) 2 1.5 3 1.5 28 82 (110) 12 12 1 (P) R port (5 port only) 5 port (A) 2 (A) 2 12 12 1 (P) 3 (R) 3 (R) 32 16 40 R port (5 port only) 3 x 1/4 53.2 25 25 * 0.5 MPa supply 63.5 F .O.F .* 40 N T.T. 45 Foot pedal VM220-02-40A VM230-02-40A 3 x 6.5 mounting hole Symbol 2 port 54 71 (A) 2 152 12 10 159 1 (P) 177 3 port (A) 2 1/4 2(A) T.T. 12 10 1 (P)