CEx-OMG0106 Examination of Load Rate an A 0.25 B 0.375 C 0.25 D 0.073 an 0.948 Decision an1 ML2B32 is selected 20 . With Guide 1. Operating Conditions Model : ML2B25 Load : 30N Speed , Va : 350mm/s Mounting Direction : upon wall W The weight of table is considered as 0 in this case. However, during actual application, it should be taken into consideration. 2.
Since CHQWB series does not have an air release plug, release air from components other than the cylinder (e.g. from piping, etc.) as well. 6. When mounting the cylinder body with mounting bolts, use tightening torques in the table below as a guide. 2.
Compact Rotary Actuator Rack-and-Pinion Type/Sizes: 10, 15, 20, 30, 40 Series CRQ2 Compact Rotary Actuator Rack-and-Pinion Type/Sizes: 10, 15, 20, 30, 40 Series CRQ2 Piping can be installed from one end Body can be used as a flange Compact design saves mounting space Uses internal cushioning 10, 15 : Rubber bumper 20, 30, 40: Air cushion 10: 17mm 15: 20mm 20: 29mm 30: 33mm 40: 37mm 2 auto
Note 9) The specifications of the IDFA6E-20 are the same as those of the IDF6E-20 (page 29) aside from the compliant standards. SFD LLB Construction Principle (Air/Refrigerant Circuit) AD Humid, hot air coming into the air dryer will be cooled down by a cooler re-heater (heat exchanger).
Furthermore, by connecting an input block, a maximum 32 sensor signal inputs are possible. SI unit for AS-i As a AS-i slave unit, this kit is capable of up to 4 or 8 points of solenoid valve ON and OFF control. Furthermore, by connecting an inmput block, a maximun 4 or 8 sensor signal inputs are possible.
DB9 network connector is available as an option. Maximum baud rate: 12Mb GW unit IP65 SI unit with SV valves: IP65 SI unit with VQC valves: IP67 64 64 ?
Furthermore, when used with the downstream side open, use caution as there is a danger that cavitation will easily occur. 1. Never use in an atmosphere of explosive gases. The structure of switches is not intended to prevent explosion. Never use in an atmosphere with an explosive gas since this may cause a serious explosion. 2.
Origin Home Switch Infotmation LX series actuators are available with an optional photo micro sensor as an origin home switch to detect when the actuator is fully retracted. The LCOC seies positioning drjver requires an input from the origin home switch or some other sensor when homing the actuator.
Do not perform unlocking while an external force such as a load or spring force is being applied. This is very dangerous because the cylinder will move suddenly.
Use caution when handling a cylinder, which is running at a high speed and a high frequency, because the surface of a cylinder tube could get so hot enough as to cause you get burned. 4. Do not use an air cylinder as an air-hydro cylinder. If it uses turbine oil in place of fluids for cylinder, it may result in oil leakage. 5. The oil stuck to the cylinder is grease. 6.
(mm) D-A90V D-A96V D-A93V 22 Bore size D-M9V D-F9WV D-M9 D-F9W D-A90 D-A96 D-A93 (mm) 32 20 32 Mounting pattern q, w 35 Mounting pattern e 20 12 Mounting of Auto Switch As shown below, there are 3 ways to mount the auto switch according to 3 types of electrical entries. Insert the auto switch into the switch groove.
(mm) D-A90V D-A96V D-A93V 22 Bore size D-M9V D-F9WV D-M9 D-F9W D-A90 D-A96 D-A93 (mm) 32 20 32 Mounting pattern q, w 35 Mounting pattern e 20 12 Mounting of Auto Switch As shown below, there are 3 ways to mount the auto switch according to 3 types of electrical entries. Insert the auto switch into the switch groove.
The programmed Key(s) will give an output signal for as long as the key is depressed.
Besides, the whole accuracy after mounting on an equipment may be varied depending on the mounting condition and surroundings. As an equipment, calibration should be done by customer.
Besides, the whole accuracy after mounting on an equipment may be varied depending on the mounting condition and surroundings. As an equipment, calibration should be done by customer.
These switches are not rated as explosion proof. Never use in the presence of an explosive gas as this may cause a serious explosion. Pressure Setting Caution 2. Do not use in an environment where a strong magnetic field is present. 1. The switching setting indication scale shows the set value for pressure decrease.
2 r AS t q w AS-FE r y KE t u AS-FG i i o AS-FP !0 u AS-FM y !3 w !1 AS-D Meter-in type Meter-out type e Meter-in type Meter-out type AS-T ASP ASN Component Parts Component Parts AQ No.
Front matter 7 16 Flow Characteristics Note) Use this graph as a guide. In the case of obtaining an accurate flow rate, refer to front matter pages 1 to 6.
Speed Adjustment Throttle speed controller, such as Series AS, is recommended for speed adjustment.