Maximum piston speed: 1000 mm/s It can be used at 50 to 1000 mm/s provided that it is within the allowable kinetic energy range.
Mounting clearance (mm) Bore size (mm) 40 20 46 25 56 32 Clearance 6 Series CU Auto Switch Specifications Auto Switch Common Specifications Type Reed switch Solid state switch Leakage current None 3-wire: 100A or less; 2-wire: 0.8mA or less Operating time 1.2ms 1ms or less Impact resistance 300m/s 50M or more at 500VDC (between lead wire and case) 1000m/s Insulation resistance 1500VAC for
0.5 s/1 s/2 s/5 s Output protection Short-circuit protection Output mode Select from hysteresis mode, window comparator mode, accumulated output mode, or accumulated pulse output mode.
Cylinder Bore Sizes (in inches) Valve Type Cv Type* 34 1 118 112 2 214 212 3 314 4 6 Micro-Line 0.11 SA F S S LTV 0.18 SA,DA F F F F M M M M S S Nova 1.00 SA,DA F F F F F F F M M Duramatic 0.18 SA,DA F F F F M M M M S S Duramatic 0.63 SA,DA F F F F F M M M M Capsula 0.75 SA,DA F F F F F F M M M Capsula 3.17 SA,DA F F F FT-1, FC-1 0.13 SA F F M S 4B-1, 4W-1 0.48 SA,DA F F F F M M M S FC51,
Cylinder Bore Sizes (in inches) Valve Type Cv Type* 34 1 118 112 2 214 212 3 314 4 6 Micro-Line 0.11 SA F S S LTV 0.18 SA,DA F F F F M M M M S S Nova 1.00 SA,DA F F F F F F F M M Duramatic 0.18 SA,DA F F F F M M M M S S Duramatic 0.63 SA,DA F F F F F M M M M Capsula 0.75 SA,DA F F F F F F M M M Capsula 3.17 SA,DA F F F FT-1, FC-1 0.13 SA F F M S 4B-1, 4W-1 0.48 SA,DA F F F F M M M S FC51,
At this time, measure the discharging time and the residual pressure inside the air tank which had been left until it turned to be the normal values to determine the effective area S, using the following formula. The volume of an air tank should be selected within the specified range by corresponding to the effective area of an equipment for test.
S H H L L 11.5 8 3 5 L2 dimension DIN rail part no.
Temperature characteristics (25C standard) 3% F .S. 5% F .S. Output type Select from NPN or PNP open collector output.
Note 1) How to Order Sub-plate Note 2) VQ4000 Note 3) Electrical entry Port size P S Plug-in conduit terminal Plug lead 02 03 Rc1/4 Rc3/8 Piping B Side piping Note 1) Bottom piping type is applicable to only Rc1/4. Refer to p.1.11-46 for thread standard.
When designing an application, be sure to allow sufficient clearance for maintenance and inspections. V (mm/s) = Auto switch operating range (mm) Load operating time (ms) x 1000 In case of high piston speed, the operating time of the load can be extended by using an auto switch (D-F7NT) with built-in OFF delay timer (approx. 200ms). 4. Keep wiring as short as possible.
If the failure cannot be solved, contact SMC. 1 Displayed if an internal data error has occurred. System error 1 Not applicable 1 1 1: The switch output will be OFF when an error is generated.
of an isometric acceleration movement. 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 Rotation time (s/90)
s NVZ3000 Symbol With Subplate Body porled Vpe Base mounted type with subplate NVZ3r20 NVZ340 Cv0.25 1 1 / l \ l h u d l / l \ L E l ff NVZ32?
m/s Piston Speed m/s 19 4-3 Selection Example .
Fit an auto switch into the auto switch mounting groove to set it roughly to the mounting position for an auto switch. 4. After confirming the detecting position, tighten up the mounting screw (M2.5) attached to an auto switch, and secure the auto switch. 5. When changing the detecting position, carry out in the state of 3. 1.
s NVZ3000 Symbol With Subplate Body porled Vpe Base mounted type with subplate NVZ3r20 NVZ340 Cv0.25 1 1 / l \ l h u d l / l \ L E l ff NVZ32?
MOperation sequence diagram M Operation sequence diagram 4 output points Two-time hitting only for CH2 ON for 1 s OFF for 2 s Stop signal ONt For CH1 OFFt CH2 OFFt CH3 Power supply ON time CH4 2 s 1 s tA tA 1 s CH1 2 s 2 s 2 s 2 s OFFt 1 s 1 s 1 s 1 s CH2 2 s Two-time hitting 1 s CH3 2 s 1 s CH4 Power switch ON (Output start) Power switch OFF (Output stop) Cascade Connection (Multiple-board
For subsonic range Where P1 + 0.1013 = (1 to 2) (P2 + 0.1013) Formula based on Cv factor Q = 197.8Cv P (P2 + 0.1013) kg/h Formula based on effective area Q = 11.0S P (P2 + 0.1013) kg/h [650] (133) 0.2 [646] (120) 0.1 S = 2.8mm S = 5.9mm S = 9.2mm S = 11.7mm S = 6.3mm S = 9.7mm S = 14.4mm S = 10.8mm S = 15.3mm S = 24.8mm Flow rate Q kg/h VCS212 VCS213 VCS214 VCS215 VCS 13 VCS314 VCS315
Never use in an atmosphere of explosive gases. The construction of auto switches is not intended to prevent explosion. Never use in an atmosphere with an explosive gas since this may cause a serious explosion. 2. Do not use in an area where a magnetic field is generated.
_;aone-mK IT;frN-mTD:e7--E E-]-DE7A-fiE -fDrc76 -8.7-E ]-D:F7E]S--rD:e60]rrTD:H-7ec73C I D-C73C c0lre I D-c8oc Bole size Standard strok/Hundleths ot an inch Nole 1) Standard Auto Switch {ead wne length is 20 inchs. 1 1 I inch leads available on all mode! s by adding an L' suflix to the part number. (b(smple) D-C73 ' D-C731.