CYPSeries Do not use in an environment with temperature cycles. Consult SMC if switches are used where there are temperature cycles other than normal temperature changes, as they may be adversely affected internally. 4. Do not use in an environment where there is excessive impact shock.
Do not use in an environment with temperature cycles. Consult SMC if switches are used where there are temperature cycles other than normal temperature changes, as they may be adversely affected internally. 4. Do not use in an environment where there is excessive impact shock.
Both input and output sizes are shown for an input / output unit. In / Out size Input data "--" is displayed for an output unit. Displays input data value which is sent to an input unit or input / output unit. Output data "--" is displayed for an input unit.
Insert a flat head screwdriver into the hook section of the clip groove. q Note) Indicate the valve model no. as a label will be attached to the clip. AZ-T-VCS Valve model no. on page 17-2-42/46 Seal part no. Valve w For VCS20 OR-1860-120P Tilt the screwdriver down in direction q so that the clip slides out in direction w.
Never use them in the presence of an explosive gas, as this may cause a serious explosion 2. Do not use in an area where a magnetic field is generated. Auto switches will malfunction or magnets inside cylinders will become demagnetized if used in such an environment. (Consult with SMC regarding the availability of magnetic field resistant auto switches.) 3.
Pressure holding VXH It is not usable for an application such as holding the pressure inside of a pressure vessel because air leakage is entailed in a valve. VXF 5. When the conduit type is used as equivalent to an IP65 enclosure, install a wiring conduit etc. VX3 VXA 6.
Equipment such as an ejector is configured as an individual unit. Thus, it is possible to create a flexible system configuration in which the circuit composition and the mounting locations can be selected as desired.
Pressure piloting positively actuates a directional valves by an external air signal that comes from a remote three-way valve, such as the Micro-Line valve series. Air pressure piloting provides an economical alternative to the use of electric switches and solenoids.
Pressure piloting positively actuates a directional valves by an external air signal that comes from a remote three-way valve, such as the Micro-Line valve series. Air pressure piloting provides an economical alternative to the use of electric switches and solenoids.
Fix the outlet end of the tube so as not to swing during discharge. Prevent the drain tube from having a rise in its piping. Do not bend or crush the drain tube. When installing the product, take care not to place the product on the drain tube. For piping the drain tube to the back of the dryer, use the holder included as an accessory.
When designing an application, be sure to allow sufficient clearance for maintenance and inspections. V (mm/s) = Auto switch operating range (mm) Load operating time (ms) x 1000 In case of high piston speed, the operating time of the load can be extended by using an auto switch (D-F7NT) with built-in OFF delay timer (approx. 200ms). 4. Keep wiring as short as possible.
well as the following instructions.
I Available as double acting or single acting.
Operating conditions Note 2) An Impact body equivalent weight is the weight of an impact object without involving thrust, into which an objects total energy has been converted.), refer to the catalog of rotary actuator.
If the product is to be used in an environment containing oils or chemicals such as coolant or cleaning solvent, even for a short time, it may be adversely affected (damage, malfunction, or hardening of the lead wires). Do not use in an area where surges are generated.
If the product is to be used in an environment containing oils or chemicals such as coolant or cleaning solvent, even for a short time, it may be adversely affected (damage, malfunction, or hardening of the lead wires). Do not use in an area where surges are generated.
If the product is to be used in an environment containing oils or chemicals such as coolant or cleaning solvent, even for a short time, it may be adversely affected (damage, malfunction, or hardening of the lead wires). Do not use in an area where surges are generated.
Therefore, avoid using the product in environment where corrosive gases are present as much as possible. 2) Do not scratch the coated surface of the copper tube when removing the panels for maintenance. As the corrosion resistance can be deteriorated from the scratch position.
Since Series CHQWB does not have an air release plug, release air from components other than the cylinder (e.g. from piping, etc.) as well. 6. When mounting the cylinder body with mounting bolts, use tightening torques in the table below as a guide. 1. Use hexagon socket head cap screws (JISB1176, strength class 10.9 or higher) for cylinder mounting. (20: 2pcs, 32 to 100: 4pcs.) 2.