F/ISE W K 2-Plug H HA CB 2-P (Piping port) Y HP Counter bore depth C 4-counter bore B T T 4-J x E 0 -0.1 L Cylinder tube outer circumference: TC Hard chrome plated + special treatment WP X F GW GP 4-LD D QW PW 2 x 4-MM thread depth M W K G G Q + Stroke Z + Stroke (mm) Model B C CB D F G GP GW H HA HC HP HB HT K J x E A 10.5 181. 16.6 181. 5 33 31.5 32 30 171. 31 171. 2 4.2 171. 14 M5 x 0.8 x 7
Body Size: 10, Thread: Rc: Size 20, 25, 30, 40; M5: Size 10, Port Size: M5, Option: Standard, Semi-Standard 1: Standard, Semi-Standard 2: Z (NPT Porting requires Z, Name Plate, Caution Plate for Bowl, & Pressure Gauge in Imperial Units: psi, °F), Made to Order: X406 (0.4 MPa Setting)
Body Size: 10, Thread: Rc: Size 20, 25, 30, 40; M5: Size 10, Port Size: M5, Option: Standard, Attachment: T (T-Interface), Semi-Standard 1: Standard, Semi-Standard 2: Z (Name Plate, Caution Plate for Bowl, & Pressure Gauge in Imperial Units: psi, °F)
Body Size: -, Thread: -, Port Size: -, Option: -, Attachment: -, Semi-Standard 1: -, Semi-Standard 2: -
Body Size: 10, Thread: Rc: Size 20, 25, 30, 40; M5: Size 10, Port Size: M5, Option: Standard, Semi-Standard 1: Standard, Semi-Standard 2: NPT Porting requires Z, Name Plate, Caution Plate for Bowl, & Pressure Gauge in Imperial Units: psi, °F, Made to Order: 0.4 MPa Setting
: [Other] M, Control Side, Connection Diameter: [M5] M5x0.8, Pressure Gauge: [Not Provided] No Pressure Gauge, Size of Body: 10, Accessory: Without optional mounting parts, Set Pressure: 0.05 to 0.4 MPa, Pressure Unit: Nameplate and pressure gauge units: psi, Custom-made Specifications: 0.4 MPa setting, Handle Direction / Position: Handle downward
Do not use a stopper cylinder for intermediate stopping of loads directly connected to a cylinder, etc. The operating ranges shown in the catalog should only be used for stopping pallets on a conveyor. If loads connected directly to a cylinder, etc., are stopped with a stopper cylinder, the cylinder's thrust will become a lateral load. Please consult with SMC in this case. Danger 1.
Do not use a stopper cylinder for intermediate stopping of loads directly connected to a cylinder, etc. The operating ranges shown in the catalog should only be used for stopping pallets on a conveyor. If loads connected directly to a cylinder, etc., are stopped with a stopper cylinder, the cylinder's thrust will become a lateral load. Please consult with SMC in this case. Danger 1.
Do not use in an environment where a heat source is at a close distance. 4. Do not use in an environment where static electricity is a problem. It may cause malfunction or failure of the system. Please consult with SMC for use in such an environment. 5. Do not use in an environment where spatters are generated. There is danger of fires caused by spattering.
Next, IB is entered to find IA the moment of inertia for the rotation of shaft (A) as a + b 2 2 A = ( ) b a 2 B = m 12 No. of teeth = b 11-10-3 4 Technical Data 3: Theoretical Output 5.
Piping and Speed Conrol 1) A single 3-position pressure center solenoid valve or two 3-port solenoid valves are used. (Refer to Figure 1 or Figure 2.) 2) A meter-out-type speed controller is used for ports A and B and a meter-in speed controller is used for ports C and D.
Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. Caution: Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Warning: Danger : Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury.
Use a contact protection box.
directions for 2 hours each 100m/s2 in X, Y, Z directions 3 times each 01 type: R 1/8, M5 x 0.8; T1 type: NPT 1/8, M5 x 0.8 Front case: PBT; Rear case: PBT; Piping port: C3602 (electroless nickel plated) Sensor pressure: Silicon; O-ring: NBR Material Weight 43g (without lead wire) Note 1) When switch output is selected, analog output is not available.
140.5 LVR50-V19 22 80 120 169 C F E Breathing port M5 x 0.8 J Tube extensions 4 x 7 Mounting hole 1/8 (Rc, NPT) Pilot port A H D B G Breathing port M5 x 0.8 Model A B C D E LVR20-T07(06) 40 40 49.3 68 20.1 LVR40-T11(10) 82.5 82.5 89 115 33 IN C F Model F G H J K LVR20-T07(06) 8 27 56 33.5 126.2 LVR40-T11(10) 14 64.5 100 40 183.3 E K J J Breathing port M5 x 0.8 5 Applicable Fluids Regulator
5) () (01 MPa 0.001 MPa 1/1000) () () F // () -14No.PS-OMU0002CN-D (38L(2 ) 0.50.05 Nm ,, A(ZS-46-A1) 38L A B(ZS-46-A2) 38L B -15No.PS-OMU0002CN-D (a)(a) (b) (ZS-46-B) +(ZS-46-D) () 90 -16No.PS-OMU0002CN-D (-M5) 1/61/4 11.5 Nm (ZS-46-N) -01-N01 23 35 Nm -C4H-C6H-N7H-C4L-C6L-N7L 1/61/4 11.5 Nm -17No.PS-OMU0002CN-D -18No.PS-OMU0002CN-D FG () () No.
CJ1 CJP CJ2 CM2 U1 A H MM NDH10 U1 NX1 Z R2 Y Bore size (mm) 20 25, 32 40 Applicable bore size (mm) 20 25, 32 40 NDH10 R1 A A1 NX E1 L1 MM Part no.
2 A A-A' Piston rod section A' !1 !3 !4 Component Parts Note Description Material No.