SI unit for CC-Link Station number setting Setting Setting range x10 0 to 6 x1 0 to 9 : The station number should be set within the range of 01 to 64. If the number is set to 00, or to 65 or above, the L ERR LED will turn on. : The station number must not be duplicated, this will cause an error. : The default setting is 00.
air inlet 475 1030 950 direction (Symbol: 3) Ventilation direction (Symbol: 2) Ventilation IDF100150F 6-3 Outer dimensions 6 5 IDX-OM-M050 Air Dryer 6 References 6-4 Electric wiring diagram [IDF100F/125F-30-] GFCI PE TB1 THR MC1 CM OLR MC2 FM1 FM2 PRR HM MC1 SWL PLC TB2 Y0 1 MC1 COM0 2 Y3 3 MC1 Y1 COM3 4 MC2 PRS1 X4 5 P 6 PRR COM1 Symbol Description X0 L CM Refrigerating compressor Y2 THR X1
Switch for setting address X1 and X10 3 B RATE Communication speed The switch to set the communication speed of the controller IF communication line.
Y axis [Axis speed calculation] Target position Composite speed Composite travel distance =((X2-X1)2+(Y2-Y1)2+(Z2-Z1)2) (X2, Y2, Z2) Xaxis speed = ((X2-X1)/ Composite travel distance) Composite speed Y axis speed = ((Y2-Y1)/ Composite travel distance) X axis Composite speed Z axis speed = ((Z2-Z1)/ Composite travel distance) Current position Composite speed (X1, Y1, Z1) Z axis Caution
D-M9mA DC (+) Brown M2.5 x 4L Slotted set screw Main circuit of switch OUT Black Indicator light SMC 4 DC (-) Blue 2.8 2.7 24 D-M9BA 0.2 3 3.2 4 OUT (+) Brown 6 Most sensitive position Main circuit of switch OUT (-) Blue Indicator light/Display method ON OFF Operating range Display Red Green Red Optimum operating position 388 Made to Order Pilot Valve: SF4 SGC 2 2 1 A 05 G 10 1 T Z B1 A L S X1
Front view Mounting holes on the top Mounting holes Theread size Name Type Mounting hole Main body M5 Side Support A Mounting hole M5 Side Support B Mounting Tap M6 x1 Side support A Side support B MY-S25A MY-S25B Mounting holes Mounting taps Installation of work Use 4 threaded holes on the top of slider for installation of work.
1 u u x100 x10 x1 IP address setting switches Switch to set the 4th byte of the IP address by X1, X10 and X100. !7 i !2 i MS, NS Communication status LED Displays the status of the EtherNet/IPTM communication t o ENC z Encoder connector (16 pins) Axis 1: Connect the actuator cable. !0 MOT z Motor power connector (6 pins) !8 @1 !
(X1) Set lower bits of the station. The CC-Link address setting at the time of the factory shipment is set in 01".
Address setting switch (x1): Sets the 1 digit of the DeviceNet node address. Data Rate switch: Sets DeviceNet communication speed.
Extended cyclic occupied units RX/RY stations 1 15 1.10 x1 2 64/64 8/8 2 15 1.10 x1 4 128/128 16/16 3 15 2.00 x8 2 384/384 64/64 4 15 2.00 x8 4 896/896 128/128 5 31 2.00 x8 2 384/384 64/64 6 31 2.00 x8 4 896/896 128/128 7 63 2.00 x8 4 896/896 128/128 8 127 2.00 x8 4 896/896 128/128 * The last register of the bit area (16 bits) cannot be used as it is allocated for the system area.
gasket positioning 22.2 die-cast hole 36 (EA, EB port) 1/8 39.4 L plug connector (L) : SY7120-L(-F ) C8, N9 C10, N11 1 2 M plug connector (M): SY7120-M(-F ) C8, N9 C10, N11 1 2 DIN terminal (D): SY7120-D(-F ) C8, N9 C10, N11 1 2 M8 connector (W0): SY7120-W0(-F ) C8, N9 C10, N11 1 2 Applicable cable O.D. 3.5 to 7 Approx. 300 (Lead wire length) 66 58.5 Max. 10 47.2 31.5 [38.5] 32.1 16.1 36 M8 x1
Y1 S + Stroke Y1 X1 BB Z + Stroke ZZ + 2 strokes (mm) Stroke range (mm) Bore size (mm) C B BB GA LX P LW LT F J LH NA T SS S Z X1 Y1 R M CD 32 62 58 38 11 16 158 220 11 32 11 40 8 3/8 40 222 37 30 39 32 M10 x 1.25 25 to 800 13 0.15 0.13 40 69 65 45 11 12 158 220 11 32 11 43 8 3/8 46 222 36 33 42 32 M10 x 1.25 25 to 800 13 50 85 76 52 14 15 176 241 13 35 11 50 8 1/2 58 246 43 37 46 40 M10
(X1) Set lower bits of the station. The CC-Link address setting at the time of the factory shipment is set in 01".
STO 13.3.3 3.2.2 ISO/EN ISO 13849-1 3 PL d 24 V EMG S4 S3 KM1 S2 KM1 K3 +24 V XS0 XS1 Z00 Z10 Z20 KM1 MELSEC (QS90SR2S) KM1 X0 COM0 24G X1 COM1 Z01 Z11 Z21 CN8 STO1 S1 EMG () STO2 STOCO M K3 TOFB1 TOFCOM 0 V TOFB2 20 S1STO (STO ) S2(STO ) S3ON S4OFF KM1 K3 EMG CN3 EM1 EM2 M . STOS1EMG0 STO[AL. 63 STO] 13.
For actuators with a stroke less than 1000mm, set parameter PE02 (Feed function selection) to 0 and the "Feed length multiplication (STM) (Multiplier)" value to x1. For actuators with a stroke more than 1000mm, set parameter PE02 (Feed function selection) to 0001 and the "Feed length multiplication (STM) (Multiplier)" value to x10.
range) K1 (screw length) Q2 P Zb2 JJ Eb Eb Q1 Zb1 JJ H H Eb Eb P A2 A1 L (Counterbore depth) Detail drawing of Zb2 (adjustable range) 2 x 2-LD L (Counterbore depth) Detail drawing of Zb1 (adjustable range) 2 x 2-LD MY3 Floating Bracket Mounting Dimensions (mm) Adjusting range Applicable cylinder Model Common JJ L P LD H G Ea Eb MYAJ16 MYAJ25 MYAJ40 MYAJ63 MY316 MY325 MY340 MY363 M4 x 0.7 M6 x1
GW unit setup The [Properties] screen will be displayed by double-clicking the [Interface] of the [Configuration table] window [Slot X1]. Tick the box for [Prioritized startup] in the [General] tab and press the [OK] button. The [Properties] screen will be displayed by double-clicking the Slot1 P1 or P2 (communication port using the FSU function) in the [HW Config] screen.
. = 4[V]x1% = 0.04[V]) The maximum measuring range or change in analogue output over the maximum measurement range. F.S. (Full span, Full scale) H The difference between ON and OFF points used to prevent chattering. Hysteresis can be effective in avoiding the effects of pulsation.
For actuators with a stroke less than 1000mm, set parameter PA05 (Feed function selection) to 0 and the "Feed length multiplication (STM) (Multiplier)" value to x1. For actuators with a stroke more than 1000mm, set parameter PA05 (Feed function selection) to 0001 and the "Feed length multiplication (STM) (Multiplier)" value to x10.
For actuators with a stroke less than 1000mm, set parameter PA05 (Feed function selection) to 0 and the "Feed length multiplication (STM) (Multiplier)" value to x1. For actuators with a stroke more than 1000mm, set parameter PA05 (Feed function selection) to 0001 and the "Feed length multiplication (STM) (Multiplier)" value to x10.